[1]  Harper C (2001) Handbook of materials for product design. McGraw-Hill.

[2]  Smith CS (1991) Design of submersible pressure hulls in composite materials. Marine Structures. 4(2): 141-182.

[3]  Petek A, Jurisevic B, Kuzman K, Junkar M (2009) Comparison of alternative approaches of single point incremental forming processes. J Mater Process Technol 209: 1810-1815.

[4]  Duflou J, Tunckol Y, Szekeres A, Vanherck P (2007) Experimental study on force measurements for single point incremental forming. J Mater Process Technol 189: 65-72.

[5]  Jeswiet J, Micari F, Hirt G, Bramley A, Duflou J, Allwood J (2005) Asymmetric single point incremental forming of sheet metal. Ann CIRP 54(2): 623-649.

[6]  Thibaud S, Ben Hmida R, Richard F, Malécot P (2012) A fully parametric toolbox for the simulation of single point incremental sheet forming process: Numerical feasibility and experimental validation. Simul Model Pract Th 29: 32-43.

[7]  Attanasio A, Ceretti E, Giardini C (2006) Optimization of tool path in two points incremental forming. J Mater Process Technol 177: 409-412.

[8]  Ambrogio G, Filice L, Micari F (2006) A force measuring based strategy for failure prevention in incremental forming. J Mater Process Technol 177: 413-416.

[9]  Blaha F, Langenecker B (1955) Tensile deformation of zinc crystal under ultrasonic vibration. Naturwissenschaften 42(20): 556-556.

[10] Langenecker B (1961) Work-softening of metal crystals by alternating the rate of glide strain.      Acta Metal 9: 937-940.

[11] Langenecker B (1966) Effects of ultrasound on deformation characteristics of metals. IEEE Trans Sonics Ultrason 13: 1-8.

[12] Lucas M, Gachagan A, Cardoni A (2009) Research applications and opportunities in power ultrasonics. Proc Inst Mech Eng Part C J Mech Eng Sci 223(12): 2949-2965.

[13] Winsper CE, Sansome E (1967) A review of the application of oscillatory energy to metals deforming plasticity. 8th International MTDR Conference, Manchester 1359-1360.

[14] Malygin GA (2000) Acoustoplastic effect and the stress superimposition mechanism. Phys Solid State 42: 72-78.

[15] Pohlman R, Lehfeldt E (1966) Influence of ultrasonic vibration on metallic friction. Ultrasonics 4: 178-185.

[16] Nevill GE, Brotzen FR (1957) Effect of vibration on the yield strength of a low-carbon steel. in First Technical Report, The Rice Institute, Solid Science Division, Air Force Office of Scientific Research, ARDC, Washington,.

[17] Green RE (1975) Non-linear effects of high-power ultrasonics in crystalline solids. Ultrasonics 13: 117-127.

[18] Daud Y, Lucas M, Huang Z (2007) Modelling the effects of superimposed ultrasonic vibrations on tension and compression tests of aluminium. J Mater Process Technol 186(1-3): 179-190.

[19] Petukhow VI, Abramov OV, Zubko AM, Manegin YV (1973) Extrusion of aluminium in an ultrasonic field. Light Met Age 31: 6-8.

[20] Jimma T, Kasuga Y, Iwaki N, Miyazawa O, Mori E, Katsuhiko K, Hatano H (1998) An application of ultrasonic vibration to the deep drawing process. J Mater Process Technol 80-81: 406-412.

[21] Ashida Y, Aoyama H (2007) Press forming using ultrasonic vibration. J Mater Process Technol 187-188: 118-122.

[22] Inoue M (1984) Studies on ultrasonic metal tube drawing. Mem Sagami Inst Technol 19: 1-7.

[23] Hung JC, Hung C (2005) The influence of ultrasonic vibration on hot upsetting of aluminum alloy. Ultrasonics 43: 692-698.

[24] Li L, Lang X (1994) Wire drawing with ultrasonic vibration. Wire Ind 61: 721-721.

[25] Murakawa M, Jin M, Kaewtatip P (1999) Utility of ultrasonic vibration applied to metal-forming processes. Adv Technol Plast 19-24.

[26] Murakawa M, Jin M (2001) The utility of radially and ultrasonically vibrated dies in the wire drawing process. J Mater Process Technol 113: 81-86.

[27] Siegert K, Mock A (1996) Wire drawing ultrasonically oscillating dies. J Mater Process Technol 60: 657-660.

[28] Siegert K, Ulmer J (2001) Superimposing ultrasonic waves on the dies in tube and wire drawing. J Eng Mater Technol Trans ASME 123: 517-523.

[29] Lucas M, Daud Y (2009) A finite element model of ultrasonic extrusion. 7th International Conference on Modern Practice in Stress and Vibration Analysis, pp. 181, IOP Publishing Ltd,.

[30] Rasoli MA, Abdullah A, Farzin M, Fadaei Tehrani A, Taherizadeh A (2012) Influence  of  ultrasonic vibrations  on  tube spinning  process. J Mater Process Technol 212: 1443-1452.

[31] Abedini R, Abdullah A, Alizadeh Y, Fartashvand V (2016) A Roadmap for application of high power ultrasonic vibrations in metal forming. Modares Mechanical Engineering 16(10): 323-334. (in Persian)

[32] Vahdati M, Mahdavinejad R, Amini S (2015) Investigation of the ultrasonic vibration effect in incremental sheet metal forming process. Proc Inst Mech Eng Part B J Eng Manuf 1-12.

[33] Ensminger D, Bond LJ (2012) Ultrasonics fundamentals, technologies, and applications. 3rd edn. CRC press.

[34] http://www.atlassteels.com.au

[35] Young MJR, Winsper CE, Sansome DH (1970) The effect of tool attachment on the resonant characteristics of ultrasonic waveguides. Appl Acoust 3: 217-224.

[36] http://www.3DS.com/simulia

[37] DIN 51524, Part 2.

[38] Iseki H (2001) An approximate deformation analysis and FEM analysis for the incremental bulging of sheet metal using a spherical roller. J Mater Process Technol 111: 150-154.

[39] Hussain G, Gao L (2007) A novel method to test the thinning limits of sheet-metals in negative incremental forming. Int J Mach Tools Manuf 47: 419-435.

[40] Astashev VK, Babitsky VI (2007) Ultrasonic processes and machines: Dynamics, control and applications. Springer Science & Business Media, Berlin.