[1] Lancaster JF (1999) Metallurgy of welding. Elsevier.

[2] Arora A, Zhang Z, De A, DebRoy T (2009) Strains and strain rates during friction stir welding. Scripta Materialia 61(9): 863-866.

[3] Zhi-hong FU, Di-qiu H, & Hong W (2004) Friction stir welding of aluminum alloys. Journal of Wuhan University of Technology-Mater Sci Ed 19(1): 61-64.

[4] Elangovan K, Balasubramanian V (2007) Influences of pin profile and rotational speed of the tool on the formation of friction stir processing zone in AA2219 aluminium alloy. Mat Sci Eng A-Struct 459(1-2): 7-18.

[5] Liu H, Fujii H, Maeda M, & Nogi K (2003) Tensile properties and fracture locations of friction-stir welded joints of 6061-T6 aluminum alloy. J Mater Sci Lett 22(15): 1061-1063.

[6] Uematsu Y and Tokaji (2008) Effect of re-filling probe hole on tensile failure and fatigue behaviour of friction stir spot welded joints in Al–Mg–Si alloy. Int J Fatigue 10-11: 1956-1966

 [7] Zhang Z, Li W, Shen J, Chao YJ, Li J, Ma YE (2013) Effect of backplate diffusivity on microstructure and mechanical properties of friction stir welded joints. Mater Design 50: 551-557.

[8] Liu HJ, Zhang HJ, Yu L (2011) Effect of welding speed on microstructures and mechanical properties of underwater friction stir welded 2219 aluminum alloy. Mater Design 32(3): 1548-1553.

[9] مردعلی زاده م، سلیمانی یزدی م، صفرخانیان م (1392) بررسی تجربی سرعت دورانی و سرعت پیشروی ابزار بر میکرو سختی و ریز ساختار آلیاژ آلومینیوم 5456 در فرایند جوشکاری اصطکاکی اختلاطی. مکانیک سازه­ها و شاره­ها 10-1 :(3)3.

 [10] Azizieh M, Sadeghi A, Kokabi A (2012) Microstructures of dissimilar friction stir welded joints between 1100 aluminum alloy and az31 magnesium alloy.

[11]  Badarinarayan H, Shi Y, Li X, Okamoto K (2009) Effect of tool geometry on hook formation and static strength of friction stir spot welded aluminum 5754-O sheets. Int J Mach Tool Manu 49(11): 814-823.

[12] سخایی ا ح، جلالی آقچای ع، کاظمی نصرآبادی م (1396) بررسی تجربی تاثیر پارامترهای فرآیند جوشکاری  اصطکاکی اغتشاشی نقطه­ای بر استحکام برشی اتصال ایجاد شده در آلیاژ آلومینیوم ۶T-7075. مکانیک سازه­ها و شاره­ها 66-53 :(3)7. 

 [13] Baek SW, Choi DH, Lee CY, Ahn BW, Yeon YM, Song K, Jung SB (2010) Microstructure and mechanical properties of friction stir spot welded galvanized steel. Mater Trans 51(5): 1044-1050.

[14] Zhang Z, Yang X, Zhang J, Zhou G, Xu X, Zou B (2011) Effect of welding parameters on microstructure and mechanical properties of friction stir spot welded 5052 aluminum alloy. Mater Design 32(8-9): 4461-4470.

 [15] Shen Z, Yang X, Zhang Z, Cui L, Li T (2013) Microstructure and failure mechanisms of refill friction stir spot welded 7075-T6 aluminum alloy joints. Mater Design 44: 476-486.

[16] Khodir SA, Toshiya Sh (2013) stir welded joints. Materials & Design 50: 551-557.

[17] Khodir SA, Shibayanagi T (2007) Microstructure and mechanical properties of friction stir welded dissimilar aluminum joints of AA2024-T3 and AA7075-T6. Mater Trans 48(7): 1928-1937.

[18] ASM metals handbook (1991) Heat treating. 4: 1544-1562.

[19] Azizi A, Aalami Aleagha ME, Moradi H (2015) Investigation of thermal, mechanical and microstructural properties of 7000 series Aluminum alloys welding using friction stir welding process. Modares Mechanical Engineering 14(14).

[20] Ju-Ri Kim, Eun-Yeong Ahn, Hrishikesh Das, Yong-Ha Jeong, Sung-Tae Hong, Michael Miles, and Kwang-Jin Lee (2017) Effect of Tool Geometry and Process Parameters on Mechanical Properties of Friction Stir Spot Welded Dissimilar Aluminum Alloys. Int J Precis Eng Man 18(3): 1-8.

 [21] Lotfi A (2014) The microstructure and mechanical properties of friction stir welded 7075-T6 aluminum alloy by the use of Design of Experiment. Modares Mechanical Engineering 14(3): 17-26.

[22] Tutar M, Aydin H, Yuce C, Yavuz N, Bayram A (2014) The optimisation of process parameters for friction stir spot-welded AA3003-H12 aluminium alloy using a Taguchi orthogonal array. Mater Design 63: 789-797.

[23] Paidar M, Khodabandeh A, Sarab ML, Taheri M (2015) Effect of welding parameters (plunge depths of shoulder, pin geometry, and tool rotational speed) on the failure mode and stir zone characteristics of friction stir spot welded aluminum 2024-T3 sheets. J Mech Sci Technol 29(11): 4639-4644.

[24] Sajed M, Bisadi H (2016) Experimental failure study of friction stir spot welded similar and dissimilar aluminum alloys. Weld World 60(1): 33-40.

[25] Song X, Ke Xing, Liu L, Huang LFC, (2014) Effect of plunge speeds on hook geometries and mechanical properties in friction stir spot welding of A6061-T6 sheets. Int J Adv Manuf Tech 71: 2003-2010.

[26] http://www.wilsonsmetals.com/datasheets.

[27] Vijay S, Eswar Y, Radovan K (2007) Investigation of the Friction Stir Lap Welding of Aluminum Alloys AA 5182 and AA 6022. J Mater Eng Perform 16(4): 477

[28] Sun YF, Fujii HN, Okitsu TY (2013) Microstructure and mechanical properties of dissimilar Al alloy/steel joints prepared by a flat spot friction stir welding technique. Mater Design 47: 350-357.