[1] Heavy Fabrication Division Dillinger Hütte GTS (2008) www.dillinger.de.

[2] Rasti A, Sattari-Far I, Salehi M, Karimnia V (2014) Optimal design of geometry and finite element analysis of stress in welded joint of internal stiffener ring and cylinder made of high strength aluminium alloy. Journal of Solid and Fluid Mechanics4 (1): 13-23. (In Persian)

[3] Ouyang Y, Lee M, Moon J, Kang C (2012) The effect of the blank holding force on formability in hot deep drawing of boron steel considering heat transfer phenomena and friction coefficient by simulation and experimental investigation. Proc IMechE Part B: J Eng Manuf 226 (9): 1506-1518.

[4] Kotkunde N, Deole A, Gupta A, Singh S, Aditya B (2014) Failure and formability studies in warm deep drawing of Ti–6Al–4V alloy. Mater Design 60: 540-547.

[5] Ma W, Wang B, Fu L, Zhou J, Huang M (2015) Effect of friction coefficient in deep drawing of AA6111 sheet at elevated temperatures. Trans Nonferr Met Soc China 25: 2342-2351.

[6] Xiao W, Wang B, Kang Y, Ma W, Tang X (2017) Deep drawing of aluminum alloy 7075 using hot stamping. Rare Met 36 (6): 485-493.

[7] Ma W, Wang B, Lin J, Tang X (2017) Influence of process parameters on properties of AA6082 in hot forming process. Trans Nonferr Met Soc China 27: 2454-2463.

[8] Wang X, Li J, Deng L, Li J (2017) Metal flow control during hot forming of square cups with local-thickened plates and varied friction conditions. J Mater Process Tech 253: 195-203.

[9] Maeno T, Tomobe M, Mori K, Ikeda Y (2018) Hot stamping of titanium alloy sheets using partial contact heating. 17^th International Conference on Metal Forming, Toyohashi, Japan, Procedia Manuf 15: 1149-1155.

[10] Suzuki Y, Mori K, Maeno T, Sakakibara K, Abe Y (2018) Improvement of formability using partial cooling during transfer in hot stamping of ultra-high strength steel parts. 17^th International Conference on Metal Forming, Toyohashi, Japan, Procedia Manuf 15: 1119-1126.

[11] Nakagawa Y, Mori K, Yashima S, Kaido T (2018) Springback behaviour and quenchability in hot stamping of thick sheets. 17^th International Conference on Metal Forming, Toyohashi, Japan, Procedia Manuf 15: 1071-1078.

[12] Ota E, Yogo Y, Iwata N, Nishigaki H (2019) CAE-based process design for improving formability in hot stamping with partial cooling. J Mater Process Tech 263: 198-206.

[13] Neumann R, Schuster S, Gibmeier J, Bohlke T (2019) Two-scale simulation of the hot stamping process based on a Hashin–Shtrikman type mean field model. J Mater Process Tech 267: 124-140.

[14] Kou S (2002) Welding Metallurgy. 2^nd Edition, John Wiley & Sons, ISBN: 9780471434917.

[15] Marciniak Z, Duncan JL, Hu SJ (2002) Mechanics of Sheet Metal Forming. 2nd edn. Butterworth-Heinemann 108-128.

[16] Lange K (1985) Handbook of Metal Forming. Soc Manuf Eng 20.1-20.69.

[17] Holmquist TJ (1987) Strength and Fracture Characteristics of HY-80, HY-100 and HY-130 Steels Subjected to Various Strains, Strain Rates, Temperatures, and Pressures. Naval Surface Warfare Center, Maryland.

[18] Hosford WF, Caddell RM (2007) Metal Forming: Mechanics and Metallurgy, Camb Univ Press, 3rd edn.

[19] Schoof C, Goland L, Lo D (2007) Pressurized rescue module system hull and transfer skirt design and experimental validation. OCEANS Conference, Vancouver, BC 1-8.

[20] Oehler G, Kaiser F (1973) Blanking, Punching, and Drawing Tools. 6th edn. Berlin/Heidelberg/ New York, Springer, In German.

[21] Klocke F (2013) Manufacturing processes 4: Forming. Translation from the German edition: Fertigungsverfahren 4: Umformen, Springer.

[22] Sellin W (1931) Handbook of Drawing Technology. Berlin, Springer, In German.

[23] MatWeb: Online Materials Information Resource (1996-2020) www.matweb.com.

[24] Bolt PJ, Lamboo NAPM, Rozier PJCM (2011) Feasibility of warm drawing of aluminium products. J Mater Process Tech 115: 118-121.

[25] Dassault Systèmes (2002-2020) www.3DS.com.

[26] Johnson GR, Cook WH (1985) Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures. Eng Fract Mech 21(1): 31-48.

[27] Lange K (1985) Handbook of Metal Forming. Soc Manuf Eng 6.21.

[28] Schey J (1983) Tribology in Metal-working: Lubrication, Friction, and Wear. Am Soc Met.

[29] Ghaforian Nosrati H, Gerdooei M, Falahati Naghibi M (2015) A new approach to identify the ductile damage constants of seamed metallic tube using hydro-bulging process. Journal of Solid and Fluid Mechanics 5(2): 139-151. (In Persian)