[1] Olsson U (2006) Aerospace propulsion from insects to spaceflight.

[2] Tacina R (1990) Low NO (x) potential of gas turbine engines. in 28th Aerospace Sciences Meeting.

[3] Saboohi Z, Ommi F, Akbari MJATE (2018) Multi-objective optimization approach toward conceptual design of gas turbine combustor. Appl Therm Eng 148: 1210-1223

[4] Heath CM, et al. (2010) Optical characterization of a multipoint lean direct injector for gas turbine combustors: Velocity and fuel drop size measurements. in ASME Turbo Expo 2010: Power for Land, Sea, and Air.

[5] Lieuwen T, McManus K (2003) Introduction: Combustion dynamics in lean-premixed prevaporized (LPP) gas turbines. J Propul Power 19(5): 721-721.

[6] Mosier S, Pierce R (1980) Advanced combustion systems for stationary gas turbine engines: Volume I. Review and preliminary evaluation. EPA-600.

[7] El-Asrag H, Ham F, Pitsch H (2007) Simulation of a lean direct injection combustor for the next high speed civil transport (HSCT) vehicle combustion systems. Annual Research Briefs.

[8] Khosravy el_Hossaini M (2013) Review of the new combustion technologies in modern gas turbines, in Progress in Gas Turbine Performance. InTech.

[9] Alkabie H, Andrews G, Ahmad N (1988) Lean low NOx primary zones using radial swirlers. in ASME 1988 International Gas Turbine and Aeroengine Congress and Exposition.

[10] Anderson DN (1981) Ultra-lean combustion at high inlet temperatures. in ASME 1981 International Gas Turbine Conference and Products Show.

[11] Hussain UA, et al. (1988) Low NOx primary zones using jet mixing shear layer combustion. in ASME 1988 International Gas Turbine and Aeroengine Congress and Exposition.

[12] Ajmani K, Mongia HC, Lee P (2017) CFD evaluation of A 3rd generation LDI combustor. in 53rd AIAA/SAE/ASEE Joint Propulsion Conference.

[13] Fu Y, Jeng SM, Tacina R (2005) Characteristics of the swirling flow generated by an axial swirler. in ASME Turbo Expo 2005: Power for Land, Sea, and Air.

[14] Cai J, Jeng SM, Tacina R (2005) The structure of a swirl-stabilized reacting spray issued from an axial swirler. in 43rd AIAA Aerospace Sciences Meeting and Exhibit.

[15] Tedder SA, et al. (2014) Fundamental study of a single point lean direct injector. Part I: effect of air swirler angle and injector tip location on spray characteristics. in 50th AIAA/ASME/SAE/ASEE Joint Propulsion Conference.

[16] Davoudzadeh F, Liu NS, Moder JP (2006) Investigation of swirling air flows generated by axial swirlers in a flame tube. in ASME Turbo Expo 2006: Power for Land, Sea, and Air.

[17] Dewanji D, et al. (2012) Investigation of flow characteristics in lean direct injection combustors. J Propul Power 28(1): 181-196.

[18] Ajmani K, Mongia H, Lee P (2013) Evaluation of CFD best practices for combustor design: Part I-Non-Reacting flows. in 51st AIAA Aerospace Sciences Meeting including the New Horizons Forum and Aerospace Exposition.

[19] Dewanji D (2012) Flow characteristics in lean direct injection combustors. Delft: TU Delft Ph.D. Thesis.

[20] Wilcox DC (1998) Turbulence modeling for CFD. Vol. 2.: DCW industries La Canada, CA.

[21] German A, Mahmud TJF (2005) Modelling of non-premixed swirl burner flows using a Reynolds-stress turbulence closure. Fuel 84(5): 583-594.

[22] امی ا ع د ف ا (1395) بررسی اثر پارامترهای پاشش بر کاهش قطر قطرات در انژکتورهای دوپایه دوفاز مهندسی هوافضا. دانشگاه تربیت مدرس تهران.

[23] Anderson JD, Wendt J (1995) Computational fluid dynamics. Vol. 206. Springer.

[24] Tacina R, Mao CP, Wey C (2003) Experimental investigation of a multiplex fuel injector module for low emission combustors. in 41st Aerospace Sciences Meeting and Exhibit.