Determination of Hydraulic Jacking Mechanism and Maximum Allowable Grout Pressure during Grout Injection in Anisotropic Rocks | ||
| Journal of Mining and Environment | ||
| دوره 12، شماره 2، تیر 2021، صفحه 589-603 اصل مقاله (4.19 M) | ||
| نوع مقاله: Original Research Paper | ||
| شناسه دیجیتال (DOI): 10.22044/jme.2021.10873.2063 | ||
| نویسندگان | ||
| A. Majdi* ؛ M. Yazdani | ||
| School of Mining Engineering, College of Engineering, University of Tehran, Tehran, Iran | ||
| چکیده | ||
| The hydraulic jacking refers to the process of crack growth of the pre-existing joints in the rock mass under grout pressure above the minimum in-situ stress. Thus it is essential to understand the resistance behavior of the joints and maximum grout pressure. This paper describes a novel method for determining the hydraulic jacking occurrence in anisotropic rock mass based on the principle of fracture mechanics. This method is established on three stage developments: developing an equation in order to calculate the equivalent stress intensity factor at the joint tip, determining the fracture toughness by employing the Brazilian disc test with a loading rate of 0.1 MPa/s on the rock cored samples, and assessing the stability of joints using the maximum tangential stress criterion. By comparing the joint stress intensity factor and fracture toughness in the direction of rock anisotropy, the joint stability is evaluated. Then the maximum allowable grout pressure is analytically formulated as a function of fracture toughness in order to avoid the unwanted deformations in the joints (i.e. jacking) during grouting. In order to validate the proposed method, the data obtained from the boreholes used to construct water curtain at the Sanandaj Azad Dam in phyllite rocks are analyzed. Finally, it is concluded that the growth and expansion of the joints due to the instability under grout pressure leads to an increased cement take and the occurrence of hydraulic jacking. In addition, the proposed equation for computing maximum allowable grout pressure provides an acceptable agreement with the existing empirical rules and the results of the field data. | ||
| کلیدواژهها | ||
| Hydraulic jacking؛ Anisotropic rock؛ Brazilian disc test؛ Maximum allowable grout pressure؛ Sanandaj Azad Dam | ||
| مراجع | ||
|
[1]. Brantberger, M., Stille, H. and Eriksson, M. (2000). Controlling grout spreading in tunnel grouting—analyses and developments of the GIN-method. Tunnelling and Underground Space Technology. 15 (4): 343-352.
[2]. Gothäll, R. and Stille, H. (2009). Fracture dilation during grouting. Tunnelling and underground space technology. 24 (2): 126-135.
[3]. Rafi, J.Y. and Stille, H. (2015). Basic mechanism of elastic jacking and impact of fracture aperture change on grout spread, transmissivity and penetrability. Tunnelling and Underground Space Technology. 49: 174-187.
[4]. Saouma, V.E., Ayari, M.L. and Leavell, D. A. (1987). Mixed mode crack propagation in homogeneous anisotropic solids. Engineering Fracture Mechanics. 27 (2): 171-184.
[5]. Irwin, G.R. (1957). Analysis of stresses and strains near the end of a crack traversing a plate.
[6]. Hoek, E. and Bieniawski, Z.T. (1965). Brittle fracture propagation in rock under compression. International Journal of Fracture Mechanics. 1 (3): 137-155.
[7]. Khosravi, M.H., Majdi, A., Pipatpongsa, T. and Ohta, H. (2008). A Fracture Mechanics Approach for Hydraulic Fracturing In Situ Stress Measurements. In The 10th JSCE International Summer Symposium (pp. 153-156).
[8]. Majdi, A. and Amini, M. (2011). Analysis of geo-structural defects in flexural toppling failure. International Journal of Rock Mechanics and Mining Sciences. 48 (2): 175-186.
[9]. Majdi, A. and Mirzazade, A. (2017). Prediction of Minimal Rock Mass Grouting Pressure Based on Newton’s Second Law and Principles of Fracture Mechanics. In 51st US Rock Mechanics/Geomechanics Symposium. American Rock Mechanics Association.
[10]. Krietsch, H., Gischig, V., Evans, K., Doetsch, J., Dutler, N.O., Valley, B. and Amann, F. (2019). Stress measurements for an in situ stimulation experiment in crystalline rock: integration of induced seismicity, stress relief and hydraulic methods. Rock Mechanics and Rock Engineering. 52 (2): 517-542.
[11]. Dutler, N., Nejati, M., Valley, B., Amann, F. and Molinari, G. (2018). On the link between fracture toughness, tensile strength, and fracture process zone in anisotropic rocks. Engineering Fracture Mechanics. 201: 56-79.
[12]. Amadei, B. (2012). Rock anisotropy and the theory of stress measurements (Vol. 2). Springer Science & Business Media.
[13]. Nasseri, M.H.B. and Mohanty, B. (2008). Fracture toughness anisotropy in granitic rocks. International Journal of Rock Mechanics and Mining Sciences. 45 (2): 167-193.
[14]. Nasseri, M.H.B., Grasselli, G. and Mohanty, B. (2010). Fracture toughness and fracture roughness in anisotropic granitic rocks. Rock Mechanics and Rock Engineering. 43 (4): 403-415.
[15]. Chandler, M.R., Meredith, P.G., Brantut, N. and Crawford, B. R. (2016). Fracture toughness anisotropy in shale. Journal of Geophysical Research: Solid Earth. 121 (3): 1706-1729.
[16]. Aminzadeh, A., Fahimifar, A. and Nejati, M. (2019). On Brazilian disk test for mixed-mode I/II fracture toughness experiments of anisotropic rocks. Theoretical and Applied Fracture Mechanics. 102: 222-238.
[17]. Nejati, M., Aminzadeh, A., Amann, F., Saar, M.O. and Driesner, T. (2020). Mode I fracture growth in anisotropic rocks: Theory and experiment. International Journal of Solids and Structures. 195: 74-90.
[18]. Nejati, M., Bahrami, B., Ayatollahi, M.R. and Driesner, T. (2021). On the anisotropy of shear fracture toughness in rocks. Theoretical and Applied Fracture Mechanics. 113: 102946.
[19]. Aliha, M.R.M. and Ayatollahi, M.R. (2014). Rock fracture toughness study using cracked chevron notched Brazilian disc specimen under pure modes I and II loading–A statistical approach. Theoretical and Applied Fracture Mechanics. 69: 17-25.
[20]. Funatsu, T., Kuruppu, M. and Matsui, K. (2014). Effects of temperature and confining pressure on mixed-mode (I–II) and mode II fracture toughness of Kimachi sandstone. International Journal of Rock Mechanics and Mining Sciences. (67): 1-8.
[21]. Majdi, A., Bagheri, H. and Pourrahimian, Y. (2005). A study of grout ability of Shivashan earth dam, foundation and the corresponding abutments. In 6th International Conference on Ground Improvement Techniques, Coimbra, Portugal (pp. 415-421).
[22]. READING, C.O.B. TECH. (Engineering Physics).
[23]. Ayari, M.L. and Ye, Z. (1995). Maximum strain theory for mixed mode crack propagation in anisotropic solids. Engineering fracture mechanics. 52 (3): 389-400.
[24]. Moye, D.G. (1967). Diamond drilling for foundation exploration. Inst Engrs Civil Eng Trans/Australia/.
[25]. Barton, B. and Bandis, S. (1985). Bakhtark. Strength deformation and conductivity coupling of rock joints. In International journal of rock mechanics and mining sciences & geomechanics abstracts (Vol. 22, No. 3, pp. 121-140).
[26]. Fransson, Å. and Gustafson, G. (2000). The use of transmissivity data from the probe holes for predicting tunnel grouting: Analyses of data from the access tunnel to the Äspö hard rock laboratory. Tunnelling and Underground Space Technology. 15 (4): 365-368.
[27]. Westergaard, H.M. (1939). Bearing pressures and cracks. Trans AIME, J. Appl. Mech., 6, 49-53.
[28]. IWPCO (2006). Feasibility studies of AZAD Dam and Power Plant Project. IWPCO. Report No. 3384030/3110.
[29]. Khan, S.M. and Khraisheh, M.K. (2004). A new criterion for mixed mode fracture initiation based on the crack tip plastic core region. International Journal of Plasticity. 20 (1): 55-84.
[30]. Guo, H., Aziz, N.I. and Schmidt, L.C. (1993). Rock fracture-toughness determination by the Brazilian test. Engineering Geology. 33 (3): 177-188.
[31]. Barton, N. and Choubey, V. (1977). The shear strength of rock joints in theory and practice. Rock mechanics. 10 (1): 1-54.
[32]. A. Majdi, H.M. Ali, and K. Emad (2010). Comparative studies of physical and numerical modeling on regular discontinuities. in Analysis of Discontinuous Deformation: New Developments and Applications, pp. 539–546.
[33]. Lombardi, G. and Deere, D. (1993). Grouting design and control using the GIN principle. International water power & dam construction. 45 (6): 15-22.
[34]. Majdi, A., Pourrahimian, Y. and Bagheri, H. (2004, March). Theoretical prediction of grout-take in jointed rock masses. In 5th International Conference on Ground Improvement Techniques (pp. 22-23).
[35]. Majdi, A., Bagheri, H. and Pourrahimian, Y. (2005). A study of grout ability of Shivashan earth dam, foundation and the corresponding abutments. In 6th International Conference on Ground Improvement Techniques, Coimbra, Portugal (pp. 415-421).
[36]. Stille, H., Gustafson, G. and Hassler, L. (2012). Application of new theories and technology for grouting of dams and foundations on rock. Geotechnical and Geological Engineering. 30 (3): 603-624.
[37]. Rafi, J.Y. and Stille, H. (2014). Control of rock jacking considering spread of grout and grouting pressure. Tunnelling and Underground Space Technology. 40: 1-15.
[38]. K. Weaver and D. Bruce (2013). Dam Foundation Grouting. Revised and Expanded Edition. ASCE Press. P. 473. | ||
|
آمار تعداد مشاهده مقاله: 436 تعداد دریافت فایل اصل مقاله: 518 |
||