Determining an Appropriate range for the Number of Cuboid Lifters in Ball Mills using DEM | ||
| Journal of Mining and Environment | ||
| مقاله 17، دوره 12، شماره 3، مهر 2021، صفحه 845-862 اصل مقاله (12.71 M) | ||
| نوع مقاله: Original Research Paper | ||
| شناسه دیجیتال (DOI): 10.22044/jme.2021.11052.2081 | ||
| نویسندگان | ||
| M. Jahani Chegeni؛ S. Kolahi | ||
| Faculty of Mining, Petroleum and Geophysics Engineering, Shahrood University of Technology, Shahrood, Iran | ||
| چکیده | ||
| The number of lifters in the liner of ball mills and the mill rotation speed are among the most significant factors affecting the behavior of grinding charge (balls) and their motion trajectory, and consequently, the comminution mechanism in these mills. In this research, in order to find a suitable range for the number of lifters in the liner of ball mills, the DEM method is utilized. Initially, a pilot-scale ball mill with dimensions of 2.0 m × 1.11 m without any lifter is simulated. Afterwards, by adding, respectively, 1, 2, 4, 8, 16, 20, 26, 30, and 32 cuboid lifter(s) with dimensions of 2 m × 5 cm × 5 cm, nine other separate simulations are performed. The influences of the number of cuboid lifters on the two new factors introduced here, namely ‘head height’ (HH) and ‘impact zone length’ (IZL) at various mill speeds, that is, 70% and 80% of its critical speed (CS) are investigated. The results indicate that in order to find a suitable range for the number of lifters in the liner of ball mills, it is necessary to consider these two parameters simultaneously as the criteria for selecting the appropriate range, That is, liners that simultaneously produce both a higher HH and a greater IZL are more suitable for use in the industry. The results also demonstrate that the suitable range for the number of cuboid lifters in the liner of ball mills is between 16 and 32, which field research on the ball mills of three different plants in the industry confirms the accuracy of the results obtained in this research. Unlike the previous research works, it has now been shown that the number of ball mill lifters does not only depend on the diameter of the mill but also depends on the width, height, angle of the lifter, and generally on the type of lifter. | ||
| کلیدواژهها | ||
| DEM simulation؛ ball mills؛ Number of lifters؛ Head height (HH)؛ Impact zone length (IZL) | ||
| مراجع | ||
|
[1]. Bian, X., Wang, G., Wang, H., Wang, S. and Lv, W. (2017). “Effect of lifters and mill speed on particle behaviour, torque, and power consumption of a tumbling ball mill: Experimental study and DEM simulation”. Minerals Engineering, 105, pp. 22–35.
[2]. Wills, B.A. and Napier-Munn, T.J. (2016). “Wills' Mineral Processing Technology”. 8th Edition. Elsevier, pp. 147–180. Chapter 7.
[3]. Cleary, P.W. (1998). “Predicting charge motion, power draw, segregation and wear in ball mills using discrete element methods”. Minerals Engineering, 11, pp. 1061-1080.
[4]. Cleary, P.W. (2001). “Charge behaviour and power consumption in ball mills: sensitivity to mill operating conditions, liner geometry and charge composition”. Int. J. Miner. Process. 63, pp. 79–114.
[5]. Kalala, J.T., Bwalya, M.M. and Moys, M.H. (2005). “Discrete element method (DEM) modelling of evolving mill liner profiles due to wear. Part I: DEM validation”. Minerals Engineering 18, pp. 1386–1391.
[6]. Kalala, J.T., Bwalya, M.M. and Moys, M.H. (2005). “Discrete element method (DEM) modelling of evolving mill liner profiles due to wear. Part II. Industrial case study”. Minerals Engineering, 18, pp. 1392–1397.
[7]. Banisi, S. and Hadizadeh, M. (2007). “3-D liner wear profile measurement and analysis in industrial SAG mills”. Minerals Engineering, 20, pp. 132–139.
[8]. Yahyaei, M., Banisi, S. and Hadizadeh, M. (2009). “Modification of SAG mill liner shape based on 3-D liner wear profile measurements”. Int. J. Miner. Process. 91, pp. 111–115.
[9]. Cleary, P.W. (2001) “Recent Advances in DEM modelling of tumbling mills”, Minerals Engineering, 14, pp. 1295 – 1319.
[10]. Mishra, B.K. and Rajamani, R.K. (1992). “The discrete element method for the simulation of ball mills”. Appl. Math. Modelling, 16, pp. 598 – 604.
[11]. Powell, M.S. and McBride, A.T. (2004). “A three-dimensional analysis of media motion and grinding regions in mills”. Minerals Engineering, 17, pp. 1099–1109.
[12]. Djordjevic, N., Shi, F.N., and Morrison, R. (2004). “Determination of lifter design, speed and filling effects in AG mills by 3D DEM”. Minerals Engineering, 17, pp. 1135–1142.
[13]. Djordjevic, N. (2003). “Discrete element modelling of the influence of lifters on power draw of tumbling mills”. Minerals Engineering, 16, 331–336.
[14]. Hlungwani, O., Rikhotso, J., Dong, H., and Moys, M.H. (2003). “Further validation of DEM modeling of milling: effects of liner profile and mill speed”. Minerals Engineering, 16, 993–998.
[15]. Rosales-Marín, G., Andrade, J., Alvarado, G., Delgadill, J. A. and Tuzcu, E.T. (2019). “Study of lifter wear and breakage rates for different lifter geometries in tumbling mill: Experimental and simulation analysis using population balance model”. Minerals Engineering, 141, 105857.
[16]. Maleki-Moghaddam, M., Ghasemi, A.R., Yahyaei, M. and Banisi, S. (2015). “The impact of end-wall effect on the charge trajectory in tumbling model mills”. Int. J. Miner. Process, 144, pp. 75 – 80.
[17]. Owen, P. and Cleary, P.W. (2015). “The relationship between charge shape characteristics and fill level and lifter height for a SAG mill”. Minerals Engineering, 83, pp. 19–32.
[18]. Cleary, P.W. and Owen, P. (2018). “Development of models relating charge shape and power draw to SAG mill operating parameters and their use in devising mill operating strategies to account for liner wear”. Minerals Engineering, 117, pp. 42–62.
[19]. Hasankhoei, A.R., Maleki-Moghaddam, M., Haji-Zadeh, A., Barzgar, M.E. and Banisi, S. (2019). “On dry SAG mills end liners: Physical modeling, DEM-based characterization and industrial outcomes of a new design”. Minerals Engineering, 141, 105835.
[20]. Usman, H. (2015). “Measuring the Efficiency of the Tumbling Mill as a Function of Lifter Configurations and Operating Parameters”. A PhD thesis submitted to the Faculty and the Board of Trustees of the Colorado School of Mines.
[21]. Usman, H., Taylor, P., and Spiller, D.E. (2016). “The Effects of Lifter Configurations and Mill Speeds on the Mill Power Draw and Performance”. Proceedings of the 1st International Process Metallurgy Conference (IPMC).
[22]. Rezaeizadeh, M., Fooladi, M., Powell, M.S., and Mansouri, S.H. (2010). “Experimental observations of lifter parameters and mill operation on power draw and liner impact loading”. Minerals Engineering, 23, pp. 1182 – 1191.
[23]. Jahani Chegeni, M. and Kolahi, S. (2020). “An Investigation on Effect of Shell Liner Type on Performance of Industrial SAG Mills Using DEM”. Journal of Mining and Environment (JME), Vol. 11, No. 2, pp. 387-404.
[24]. Kolahi, S. and Jahani Chegeni, M. (2020). “Investigation of Effect of Number of Lifters on Performance of Pilot-Scale SAG Mills using Discrete Element Method”. Journal of Mining and Environment (JME), Vol. 11, No. 3, pp. 675-693.
[25]. Yahyaei, M., Powel, M.S., Toor, P., Tuxford, A. and Limpus, A. (2015). “Relining efficiency and liner design for improved plant performance”. Minerals Engineering, Vol. 83, pp. 64 – 77.
[26]. Xu, L., Luo, K., Zhao, Y., Fan, J. and Cen, K. (2019). “Influence of particle shape on liner wear in tumbling mills: A DEM study”. Powder technology, Vol. 350, pp. 26 – 35.
[27]. Xu, L., Bao, S. and Zhao, Y. (2020). “Multi-level DEM study on liner wear in tumbling mills for an engineering level approach”. Powder technology, Vol. 364, pp. 332 – 342.
[28]. Chimwani, N. and Bwalya, M.M. (2020). “Using DEM to investigate how shell liner can induce ball segregation in a ball mill”. Minerals Engineering, Vol. 151, 106311.
[29]. Banisi, S. (2016). “Advanced Comminution Textbook”. Shahid Bahonar University of Kerman, Kerman, Iran, in Persian.
[30]. Gupta, A. and Yan, D. (2016). “Mineral Processing Design and Operations - An Introduction”. 2nd edition, Elsevier.
[31]. Mular, A.L., Haibe, D.N.; and Barrett, D.J. (2002). “Mineral Processing Plant Design, Practice, and Control”. SME.
[32]. Kawatra, S.K. (2006). “Advances in comminution”. SME.
[33]. Sherman, M. and Rajamani, R.K. (1999). “The Effect of Lifter Design on Alumbrera’s SAG Mill Performance: Design Expections and Optimization”. In Proceedings of the Canadian Mineral Processors Conference, Ottawa, Canada, 255–266.
[34]. Dunne, R.C., Kawtra, K., and Young, C.A. (2019). “SME Mineral Processing and Extractive Metallurgy Handbook”. SME.
[35]. Jahani, M., Farzanegan, A. and Noaparast, M. (2015). “Investigation of screening performance of banana screens using LIGGGHTS DEM solver”. Powder Technology, 283, pp. 32–47.
[36]. Online protractor. (2021). Retrived from https://www.ginifab.com/feeds/angle_measurement/ | ||
|
آمار تعداد مشاهده مقاله: 543 تعداد دریافت فایل اصل مقاله: 980 |
||