Study of Effect of Cooling/Lubricating Fluids, Machining Parameters, and Rock Mechanical Properties on Penetration Rate in Rock Drilling Process | ||
| Journal of Mining and Environment | ||
| مقاله 16، دوره 12، شماره 3، مهر 2021، صفحه 825-843 اصل مقاله (13.17 M) | ||
| نوع مقاله: Original Research Paper | ||
| شناسه دیجیتال (DOI): 10.22044/jme.2021.11017.2078 | ||
| نویسندگان | ||
| Sh. Khosravimanesh1؛ M. Cheraghi Seifabad1؛ R. Mikaeil* 2؛ R. Bagherpour1 | ||
| 1Department of mining engineering, Isfahan University of Technology, Isfahan, Iran | ||
| 2Department of Mining and Engineering, Faculty of Environment, Urmia University of Technology, Urmia, Iran | ||
| چکیده | ||
| In most rock drilling operations, the low rate of penetration (ROP) can be primarily attributed to the presence of the cuttings produced during drilling and the thermal stresses caused by friction at the bit-rock interface, which can be exacerbated with the increasing strength, hardness, and abrasivity of the drilled rock. In order to improve ROP, drill bit lifetime, and cutting power, it is necessary to minimize the process forces due to the mechanical bit-rock interaction and the thermal stresses generated in the drill hole. Any improvement in these areas is extremely important from both the technical and the economic perspectives. This improvement can be achieved by the use of appropriate cooling/lubricating fluids in the drilling process in order to increase ROP, reduce the temperature of the drilling environment, and create a clean drill hole free of cuttings. In this work, a series of laboratory drilling tests are performed to investigate and compare ROP in the drilling of seven samples of hard and soft rock in the presence of six different cooling-lubricating fluids. The drilling tests are performed on the cubic specimens with a laboratory-scale drilling rig at several different rotation speeds and thrust forces. The statistical analyses are performed in order to investigate the relationship between ROP and the mechanical properties of the rock, properties of the fluid, and machining parameters of the drilling rig. These analyses show that under similar conditions in terms of mechanical properties of the rock using Syncool with a concentration of 1:100 and soap water with a concentration of 1:120 instead of pure water leads to the average 31% and 37% increased ROP in granite, 36% and 43% increased ROP in marble, and 47% and 61% increased ROP in travertine, respectively. These results demonstrate the good performance of these cooling/lubricating fluids in increasing ROP. | ||
| کلیدواژهها | ||
| drilling؛ rate of penetration؛ coolant-lubricant fluids؛ statistical analysis؛ linear univariate | ||
| مراجع | ||
|
[1]. Izquierdo, L.E. and Chiang, L.E. (2004). A methodology for estimation of the specific rock energy index using corrected down-the-hole drill monitoring data. Mining Technology. 113 (4): p. 225-236.
[2]. Bilgesu, H., Tetrick, L., Altmis, U., Mohaghegh, S. and Ameri, S. (1997). A new approach for the prediction of rate of penetration (ROP) values. in SPE Eastern Regional Meeting. Society of Petroleum Engineers.
[3]. Hoseinie, S., Aghababaei, H. and Pourrahimian, Y. (2008). Development of a new classification system for assessing of rock mass drillability index (RDi). International Journal of Rock Mechanics and Mining Sciences. 45 (1): p. 1-10.
[4]. Zhao, X.H., Gao, F., Li, Y.F. and Li, W. (2011). The research on the effect of drilling fluids additives on Rate of Penetration (ROP). in Advanced Materials Research, Trans Tech Publ, 2064-2071.
[5]. Long, W. (1996) The lubricating mechanisms of lubricating drilling fluids on synthetic diamond bit. Journal of Central South University of Technology. 3 (1): p. 85-87.
[6]. Westwood, A., MacMillan, N. and Kalyoncu, R. (1973). Chemomechanical effects in hard rock drilling.
[7]. Rehbinder, P., Schreiner, L. and Zhigach, K. (1944). Hardness reducers in drilling. Academy of Science, Moscow. 194 (4).
[8]. Dauncey, G. (1960). De Beers Diamond Research Laboratory. Johannesburg, South Africa, Paper.
[9]. Hammond, M. and Ravitz, S. (1963). Influence of environment on brittle fracture of silica. Journal of the American Ceramic Society. 46 (7): p. 329-332.
[10]. Selim, A., Schultz, C. and Strebig, K. (1969). The Effect of Additives on Impregnated Diamond Bit Performance. Society of Petroleum Engineers Journal. 9 (04): p. 425-433.
[11]. Cooper, G. and Berlie, J. (1976). On the influence of the flushing fluid during diamond drilling. Journal of Materials Science. 11 (9): p. 1771-1775.
[12]. Mills, J. and Westwood, A. (1978). Influence of chemomechanically active fluids on diamond wear during hard rock drilling. Journal of Materials Science. 13 (12): p. 2712-2716.
[13]. El-Shall, H., Gupta, S., Haecker, R. and Somasundaran, P. (2000). Effect of additives on drilling in hard rock. Mining Engineering. 52 (1): p. 48-52.
[14]. Rao, K., Bhatnagar, A. and Misra, B. (2002). Laboratory investigations on rotary diamond drilling. Geotechnical & Geological Engineering, 20(1): p. 1-16.
[15]. Messaoud, L. (2009). Influence of fluids on the essential parameters of rotary percussive drilling. Laboratoire d'Environnement (Tébessa), 14: p. 1-8.
[16]. Bhatnagar, A., Khandelwal, M. and Rao, K.U.M. (2010). Enhancing diamond drilling performance by the addition of non-ionic polymer to the flushing media. Mining Science and Technology (China). 20 (3): p. 400-405.
[17]. Bhatnagar, A., Khandelwal, M. and Rao, K. (2011). Laboratory investigations for the role of flushing media in diamond drilling of marble. Rock mechanics and rock engineering. 44 (3): p. 349-356.
[18]. Bhatnagar, A. and Khandelwal, M. (2012). An intelligent approach to evaluate drilling performance. Neural Computing and Applications. 21 (4): p. 763-770.
[19]. Li, W., Zhao, X., Li, Y., Ji, Y., Peng, H., Liu, L. and Yang, Q. (2015). Laboratory investigations on the effects of surfactants on rate of penetration in rotary diamond drilling. Journal of Petroleum Science and Engineering, 134: p. 114-122.
[20]. Rawal, R., Karmakar, N. and Sharma, S. (2016). Effect of fluid additives on rock drilling. in Recent Advances in Rock Engineering, Atlantis Press, 2352-5401.
[21]. Taheri, A., Qao, Q. and Chanda, E. (2016). Drilling penetration rate estimation using rock drillability characterization index. Journal of The Institution of Engineers (India): Series D. 97 (2): p. 159-170.
[22]. Wang, C. and Li, S. (2018). Evaluation of Rock Abrasiveness Based on PDC Compact Wear Model. Recent Patents on Engineering. 12 (2): p. 153-163.
[23]. Shad, H.I.A., Sereshki, F., Ataei, M. and Karamoozian, M. (2018). Prediction of rotary drilling penetration rate in iron ore oxides using rock engineering system. International Journal of Mining Science and Technology. 28 (3): p. 407-413.
[24]. Xiao, Y., Hurich, C. and Butt, S.D. (2018). Assessment of rock-bit interaction and drilling performance using elastic waves propagated by the drilling system. International Journal of Rock Mechanics and Mining Sciences, 105: p. 11-21.
[25]. Shankar, V.K., Kunar, B.M., Murthy, C.S. and Ramesh, M. (2020). Measurement of bit-rock interface temperature and wear rate of the tungsten carbide drill bit during rotary drilling. Friction. 8 (6): p. 1073-1082.
[26]. Piri, M., Hashemolhosseini, H., Mikaeil, R., Ataei, M. and Baghbanan, A. (2020). Investigation of wear resistance of drill bits with WC, Diamond-DLC, and TiAlSi coatings with respect to mechanical properties of rock. International Journal of Refractory Metals and Hard Materials, 87: p. 105113.
[27]. Liao, X., Khandelwal, M., Yang, H., Koopialipoor, M. and Murlidhar, B.R. (2020). Effects of a proper feature selection on prediction and optimization of drilling rate using intelligent techniques. Engineering with Computers, 36(2): p. 499-510.
[28]. Shangxin, F., Yujie, W., Guolai, Z., Yufei, Z., Shanyong, W., Ruilang, C. and Enshang, X. (2020). Estimation of optimal drilling efficiency and rock strength by using controllable drilling parameters in rotary non-percussive drilling. Journal of Petroleum Science and Engineering, 193: p. 107376.
[29]. Kolapo, P. (2021). Investigating the Effects of Mechanical Properties of Rocks on Specific Energy and Penetration Rate of Borehole Drilling. Geotechnical and Geological Engineering. 39 (2): p. 1715-1726.
[30]. Lawal, A.I., Kwon, S. and Onifade, M. (2021). Prediction of rock penetration rate using a novel Antlion optimized ANN and statistical modelling. Journal of African Earth Sciences, p. 104287.
[31]. Piri, M., Mikaeil, R., Hashemolhosseini, H., Baghbanan, A. and Ataei, M. (2021). Study of the effect of drill bits hardness, drilling machine operating parameters and rock mechanical parameters on noise level in hard rock drilling process. Measurement, 167: p. 108447.
[32]. Brown, E.T. (1981). Rock characterization testing and monitoring: ISRM suggested methods. Oxford, Pergamon. 171-183.
[33]. Yavuz, H., Ozkahraman, T. and Demirdag, S. (2011). Polishing experiments on surface quality of building stone tiles. Construction and Building Materials. 25 (4): p. 1707-1711.
[34]. Ersoy, A. and Waller, M. (1995). Textural characterisation of rocks. Engineering geology, 39(3-4): p. 123-136.
| ||
|
آمار تعداد مشاهده مقاله: 542 تعداد دریافت فایل اصل مقاله: 632 |
||