Interaction between One Internal Hole and Two Neighboring Joints under Uniaxial Compression using an Experimental Test and a Numerical Simulation | ||
| Journal of Mining and Environment | ||
| مقاله 6، دوره 13، شماره 2، تیر 2022، صفحه 407-420 اصل مقاله (3.52 M) | ||
| نوع مقاله: Original Research Paper | ||
| شناسه دیجیتال (DOI): 10.22044/jme.2021.11157.2095 | ||
| نویسندگان | ||
| V. Sarfarazi* 1؛ K. Asgari2؛ Sh. Mohamadi Bolban Abad3 | ||
| 1Academic Member, Department of Mining Engineering, Hamedan University of Technology, Hamedan, Iran | ||
| 2Research Scholar, Department of Mining Engineering, Shahid Bahonar University of Kerman, Kerman, Iran | ||
| 3Research Scholar, Hamedan University of Technology, Hamedan, Iran | ||
| چکیده | ||
| The interaction between an internal hole and two surrounded joints under a uniaxial compression are examined using the experimental and discrete element procedures. Inside the concrete sample, two notches and an internal hole are created. The joint angle change from 0° to 90° with an increment of 30°. The distances between the joint and the internal hole are 2 cm and 3 cm. Also the numerical models are provided. The joint angle change from 0° to 90° with an increment of 15°. The distances between the joint and the internal hole are 2 cm, 3 cm, and 4 cm. The compressive strength is 7.2 MPa. The rate of loading is 0.005 mm/s. The experiment indicates that the failure process is significantly dependent on the notch angle and the joint distance from the hole. The pattern of fracture and mechanism of failure of joints affect the shear strengths of the samples. The models with joint angles of 30° and 60° have a less compressive strength since the pure tensile failure occurs in these configurations. The model strength decreases with decrease in the join spacing. In fact, in the case that the joint spacing is 2 cm, the interaction between the hole and the neighboring joint is so strong. Consequently, the compressive strength is declined. In both approaches of the numerical simulation and experimental methods, the pattern and strength of failure are identical. | ||
| کلیدواژهها | ||
| compressive test؛ joint angle؛ joint distance؛ hole, PFC2D | ||
| مراجع | ||
|
[1]. Basu, A., Mishra, D.A. (2014). A method for estimating crack-initiation stress of rock materials by porosity. J. Geol. Soc. India., 84 397–405.
[2]. Chang, S. H., Lee, C.I. and Jeon, S. (2002). Measurement of rock fracture toughness under modes I and II and mixed-mode conditions by using disc-type specimens. Eng. Geo., 66: 79-97.
[3]. Hoek, C.D. (2014). Fracture initiation and propagation in intact rock–a revie., J. Rock Mech. Geotech. Eng., 6: 287 –300.
[4]. Lisjak, A. (2017). A 2D, fully coupled, hydro-mechanical, FDEM formulation for modelling fracturing processes in discontinuous, porous rock masses. Comput. Geotech., 8: 1–18.
[5]. Karimpouli, S., Hassani, H., Malehmir, A. (2013). Understanding the fracture role on hydrocarbon accumulation and distribution using seismic data: A case study on a carbonate reservoir from Iran. J. Appl.Geophys., 96: 98–106.
[6]. Bobet, A. and Einstein, H.H. (1998). Fracture integrate in rock-type materials under uniaxial and biaxial compression. Int. J. Rock Mech. Min. Sci., 35: 863–888.
[7]. Wong, R.H.C. (2001). Analysis of crack integrate in rock-like materials containing three flaws-Part I: experimental approach. Int. J. Rock Mech. Min. Sci., 38: 909–924.
[8]. Sagong, M. and Bobet, A. (2002). Integrate of multiple flaws in a rock-model material in uniaxial compression. Int. J. Rock Mech. Min. Sci., 39: 229–241.
[9]. Wong, L.N.Y., and Einstein, H.H. (2009). Crack integrate in molded gypsum and Carrara marble: part 1. Macroscopic observations and interpretation. Rock Mech. Rock Eng., 42: 475–511.
[10]. Wong, L.N.Y. and Einstein, H.H. (2009). Crack integrate in molded gypsum and Carrara marble: part 2-microscopic observations and interpretation. Rock Mech. Rock Eng., 42: 513–545.
[11].Yang, S.Q. (2011). Crack integrate behavior of brittle sandstone samples containing two coplanar fissures in the process of deformation failure. Eng. Fract. Mech., 78: 3059-3081.
[12] .Yang, S.Q. (2008). Experimental investigation on strength and failure behavior of pre-cracked marble under conventional triaxial compression. Int. J. Solids Struct., 45: 4796–4819.
[13]. Yang, S.Q., (2012). An experimental study of the fracture integrate behaviour of brittle sandstone specimens containing three fissures. Rock Mech. Rock Eng., 45: 563–582 .
[14]. Wong, L.N.Y. and Einstein, H.H. (2009). Systematic evaluation of cracking behavior in specimens containing single flaws under uniaxial compression. Int. J. Rock Mech. Min. Sci., 46: 239–249.
[15]. Park, C.H. and Bobet, A. (2010). Crack initiation, propagation and integrate from frictional flaws in uniaxial compression. Eng. Fract. Mech., 77: 2727–2748.
[16]. Park, C.H. and Bobet, A. (2009). Crack integrate in specimens with open and closed flaws: a comparison. Int. J. Rock Mech. Min. Sci., 46: 819–829.
[17] Kranz, R.L. (1979). Crack-crack and crack-pore interactions in stressed granite. Int. J. Rock Mech. Min. Sci., 16: 37–47 .
[18]. Lee, H.K. and Ju, J.W. (2007). A 3D stress analysis of a penny-shaped crack interacting with a spherical inclusion. Int. J. Damage Mech., 16: 331–359.
[19]. Carter, B.J. (1992). Size and stress gradient effects on fracture around cavities. Rock Mech. Rock Eng., 25:167–186 .
[20]. Carter, B.J., (1991). Primary and remote fracture around underground cavities. Int. J. Numer. Anal. Methods Geomech., 15P:1–40.
[21]. Wong, R.H.C. (2006). Experimental and numerical study on splitting failure of brittle solids containing single pore under uniaxial compression., Mech. Mater., 38: 142–159.
[22]. Bocca, P. , Carpinteri, A. and Valente, S. (1990). Size effects in the mixed mode crack propagation: softening and snap-back analysis. Eng. Fract. Mech., 35:159-170.
[23] Xu, C. and Fowell, R.J. (1994). Stress intensity factor evaluation for cracked chevron notched Brazilian disc specimens. Int. J. Rock Mech. Min. Sci., 31: 157–162.
[24]. Trädegård, A. (1998). FEM-remeshing technique applied to crack growth problems. Comput. Methods Appl. Mech. Eng., 160:115–131 .
[25]. Barani, O.R. , Khoei, A.R. and Mofid, M. (2011). Modeling of cohesive crack growth in partially saturated porous media; a study on the permeability of cohesive fracture. Int. J. Fract., 167: 15– 31.
[26]. Tan, X. H. (2015). A simulation method for perme-ability of porous media based on multiple fractal model. Int. J. Eng. Sci., 95: 76-84.
[27].Ţene, M., (2016). Algebraic multiscale method for flow in heterogeneous porous media with embedded discrete fractures. J. Comput. Phys., 321: 819 –845.
[28]. Supar, K. and Ahmad, H. (2017). XFEM modelling of multi-holes plate with single-row and staggered holes confi gurations. MATEC Web Conf. 103, 02031.
[29]. Schrefler, B.A. and Xiaoyong, Z. (1993). A fully coupled model for water flow and air flow in deformable porous media. Water Res. Res., 29: 155 –167.
[30]. Aliha, M.R. (2012). Mixed mode I/II fracture path simulation in a typical jointed rock slope. 4th Int. Conf. Crack Paths, pp:55-60.
[31]. Sukumar, N. (2001). Modeling holes and inclusions by level sets in the extended finite-element method. Comput. Meth. Appl. Mech. Eng,. 190: 6183-6200.
[32] . Gordeliy, E. and Peirce, A. (2015). Enrichment strategies and convergence properties of the XFEM for hydraulic fracture problems. Comput. Methods Appl. Mech. Eng., 283: 474-502.
[33]. Mohammadnejad, T. (2013). An extended fi nite element method for hydraulic fracture propagation in deformable porous media with the cohesive crack mode. Finite Elem. Anal. Des., 73: 77 –95.
[34]. Khoei, A.R., (2014). A mesh-independent finite element formulation for modeling crack growth in saturated porous media based on an enriched-FEM technique. Int. J. Fract., 188: 79 –108.
[35]. Gordeliy, E. and Peirce, A. (2013). Coupling schemes for modeling hydraulic fracture propagation using the XFEM. Comput. Meth. Appl. Mech. Eng., 253: 305 –322.
[36]. Dahi-Taleghani, A. and Olson, J.E. (2011). Numerical modeling of multistranded-hydraulic-fracture propagation: accounting for the interaction between induced and natural fractures. SPE J., 16: 575 –581.
[37]. Réthoré, M.A. (2007). A two-scale approach for fluid fl A t fractured porous media. Int. J. Numer. Meth. Eng., 71: 780 – 800.
[38] T.P. Cheng and K.W. Fries, Higher-orderXFEM for curved strong and weak dis-continuities, Int. J. Numer. Meth. Eng. 82 (2010) 564 –590.
[39] S. Mohammadi, XFEM Fracture Analysis of Composites, John Wiley & Sons Incorporated, 2012,
[40]. Natarajan, S., Roy Mahapatra, D. and Bordas, S.P.a. (2010). Integrating strong and weak dis continuities without integration subcells and example applications in an XFEM/ GFEM framework. Int. J. Numer. Methods Eng., 83: 269 –294.
[41] .Wong, L.N.Y. and Einstein, H.H. (2009). Crack integrate in molded gypsum and carrara marble: part 1. Macroscopic observations and interpretation. Rock Mech. Rock Eng,. 42: 475-511.
[42]. Wong, L.N.Y. and Einstein, H.H. (2009). Crack integrate in molded gypsum and carrara marble: Part 2 – Microscopic observations and interpretation. Rock Mech. Rock Eng., 42: 513 –545.
[43]. Ju, Y. (2008). A statistical model for porous structure of rocks. Sci. China, Ser. E Technol. Sci., 51: 2040 –2058.
[44]. Hedjazi, L. (2012). Application of the discrete element method to crack propagation and crack branching in a vitreous dense biopolymer material. Int. J. Solids Struct., 49:1893 –1899.
[45]. Vahab, M. and Khalili, N.(2018). X-FEM modeling of multizone hydraulic fracturing treatments within saturated porous media. Rock Mech. Rock Eng., 51: 3219 –3239.
[46]. Haddad, M. and Sepehrnoori, K. (2016). XFEM-Based CZM for the simulation of 3D multiple-cluster hydraulic fracturing in quasi-brittle shale formations. Rock Mech. Rock Eng, 49: 4731-4748.
[47]. Natarajan, S. (2011). Enriched finite element methods: advances and applications.
[48]. Rodriguez-Florez, N. (2017). The use of XFEM to assess the in fluence of intra-cortical porosity on crack propagation. Comput. Meth. Biomech. Biomed. Eng., 20: 385–392.
[49]. Florez R. (2018). Mechanics of Cortical Bone: Exploring the Micro- and Nano-Scale, Imperial College London.
[50]. Bouchard, P.O., Bay, F. and Chastel, Y. (2003). Numerical modelling of crack propagation: automatic remeshing and comparison of different criteria. Comput. Methods Appl. Mech. Eng., 192: 887–3908 .
[51]. Li, H. and Wong, L.N.Y. (2012). Influence of flaw inclination angle and loading condition on crack initiation and propagation. Int. J. Solids Struct., 49: 2482–2499.
[52]. Bobet, A. and Einstein, H.H. (1998). Numerical modeling of fracture integrate in a model rock material. Int. J. Fract., 92: 221–252 .
[53]. Hosseini-Tehrani, P. (2005). Boundary element analysis of stress intensity factor KI in some two-dimensional dynamic thermoelastic problems. Eng. Anal. Boundary Elem., 29: 232–240.
[54]. Lu, X. and Wu, W.L. (2006). A sub-region DRBEM formulation for the dynamic analysis of 2D cracks. Math. Comput. Model., 43: 76–88.
[55]. Zhang, X.P. and Wong, L.N.Y. (2013). Crack initiation, propagation and integrate in rock-like material containing two flaws: a numerical study based on bonded-particle model approach. Rock Mech. Rock Eng., 46: 1001–1021.
[56]. Ghazvinian, A., Sarfarazi, V. (2012). A study of the failure mechanism of planar non-persistent open joints using PFC2D. Rock Mech.Rock Eng., 45: 677–693.
[57]. Sarfarazi, V. (2014). Numerical simulation of the process of fracture of echelon rock joints. Rock Mech. Rock Eng., 47: 1355–1371.
[58]. Park, J.W. and Song, J.J. (2009). Numerical simulation of a direct shear test on a rock joint using a bonded-particle model. Int. J. Rock Mech. Min. Sci., 46:1315–1328.
[59]. Wu, Z. and Wong, L.N.Y. (2012). Frictional crack initiation and propagation analysis using the numerical manifold method. Comput. Geotech., 39: 38–53.
[60]. Cai, Y.C. (2013). A continuous/discontinuous deformation analysis (CDDA) method based on deformable blocks for fracture modeling. Front. Struct. Civ. Eng., 7: 369–378 .
[61]. Zhuang, X.Y. and Augarde, C. (2010). Aspects of the use of orthogonal basis functions in the element-free Galerkin method. Int. J. Numer. Meth. Eng., 81: 366–380.
[62]. Zhu, H.H. (2011). High rock slope stability analysis using the enriched meshless shepard and least squares method. Int. J. Comput. Methods, 8: 209-228.
[63. Itasca, (2004). PFC2D (Particle Flow Code in 2 Dimensions), Version 3.1 Minneapolis.
[64]. Potyondy, D.O. and Cundall, P.A. (2004). A bonded-particle model for rock. Int. J. Rock Mech. Min. Sci., 41: 1329–1364.
[65]. Zhang, X.P. and Wong, L.N.Y. (2012). Cracking processes in rock-like material containing a single flaw under uniaxial compression: a numerical study based on parallelly bonded-particle model approach. Rock Mech. Rock Eng., 45: 711–737.
[66] Lee, H. and Jeon, S. (2011) An experimental and numerical study of fracture integrate in pre cracked specimens under uniaxial compression. Int. J. Solids Struct., 48: 979-999.
[67]. Uzun Yaylacı, E., Yaylacı, M., Ölmez, H., and Birinci, A. (2020). Artificial Neural Network Calculations for A Receding Contact Problem. Computers and Concrete, 2(6): 88-99.
[68]. Yaylacı, M., Eyüboğlu, A., Adıyaman, G., Uzun Yaylacı, E., Öner, E., and Birinci, A. (2021). ssessment of different solution methods for receding contact problems in functionally graded layered mediums. Mechanics of Materials, 33(2): 99-111.
[69]. Yaylacı, M., Yaylı M., Uzun Yaylacı E., Ölmez, H., and Birinci A. (2021). Analyzing the contact problem of a functionally graded layer resting on an elastic half plane with theory of elasticity, finite element method and multilayer perceptron. Structural Engineering and Mechanics, 78(5): 585-597.
[70]. Yaylaci, M. (2016). The investigation crack problem through numerical analysis. Structural Engineering and Mechanics, 57(6): 1143-1156.
[71]. Haeri, H. and Marji, MF. (2016). Simulating the crack propagation and cracks coalescence underneath TBM disc cutters. Arabian Journal of Geosciences, 9 (2):124-130.
[72]. Lak, M., Marji, M.F. (2019). Discrete element modeling of explosion-induced fracture extension in jointed rock masses. Journal of Mining and Environment, 10 (1): 125-138.
[73]. Yavari, MD. (2021). On the propagation mechanism of cracks emanating from two neighboring holes in cubic concrete specimens under various lateral confinements. Journal of Mining and Environment (accepted for publication).
[74]. Abdollahipour, A. and Marji, MF. (2020). A thermo-hydromechanical displacement discontinuity method to model fractures in high-pressure, high-temperature environments. Renewable Energy, 153: 1488-1503.
[75]. Bakhshi, E. (2019). Hydraulic Fracture Propagation: Analytical Solutions versus Lattice Simulations. Journal of Mining and Environment, 10 (2): 451-464.
[76]. Lin, P., (2015). Experimental study of coalescencemechanisms and failure under uniaxial compression of granitecontaining multiple holes. Int J Rock Mech Min Sci., 77:557‐582.
[77]. Lin, Q., (2020). Mechanical behavior around double circular openings in a jointed rock mass under uniaxial compression. Archives of Civil and Mechanical Engineering, 20(1):19-29. | ||
|
آمار تعداد مشاهده مقاله: 687 تعداد دریافت فایل اصل مقاله: 915 |
||