Numerical Modeling of Wind Distribution Around a Tall Building in a 3D Urban Environment | ||
| Renewable Energy Research and Applications | ||
| دوره 3، شماره 1، فروردین 2022، صفحه 93-102 اصل مقاله (1.27 M) | ||
| نوع مقاله: Original Article | ||
| شناسه دیجیتال (DOI): 10.22044/rera.2021.11110.1073 | ||
| نویسندگان | ||
| M. Ahmadi؛ S.A.A. Mirjalily* ؛ Seyed A. A. Oloomi | ||
| Department of mechanical engineering, Yazd Branch, Islamic Azad University, Yazd, Iran. | ||
| چکیده | ||
| This study applies an appropriate turbulence model to simulate the wind distribution in a 3D urban area around a tall building as a bluff body which is one of the most important research topics due to the increasing concerns about human health risks due to air pollution in recent decades. Hybrid RANS/LES approach, was used to reduce computation time while maintaining computational accuracy. On the other hand, since no homogeneous direction exists in the flow in the Hybrid (RANS-LES) approach, the LES and Smagorinsky Sub Grid-Scale (SGS) approach are implemented with the standard k-ε turbulence model as RANS. To obtain more accurate results, the second-order Van Leer Method (VLM) was employed in advection terms. The sensitivity study of the input parameters shows that the intensity of the input turbulence has a significant effect on the surface pressure fluctuations. The results of velocity and pressure distribution showed a very close agreement to wind tunnel experimental data. Finally, the effects of the inflow characteristics on the peak pressure on the lateral sides is also studied. As the results, fluctuation pressure distribution was strongly dependent on the turbulence of the flow. | ||
| کلیدواژهها | ||
| Hybrid RANS-LES approach؛ Wind Distribution؛ Tall Building؛ Bluff Body؛ Pressure Distribution | ||
| مراجع | ||
|
[1] Davenport A.G. (1998). What makes a structure wind sensitive? In A.A. Balkema, The Jubileum Conference on Wind Effects on Buildings and Structures, Porto Alegre, Brazil, 1998.
[2] Zaniani J.R. et al. (2015). Examining the Possibility of using Solar Energy to Provide Warm Water using Retscreen4 Software (Case Study: Nasr Primary School of Pirbalut), Special Issue of Curr World Environ,10 (Special Issue May 2015).
[3] Mostafaeipour A. et al. (2019). Energy efficiency for cooling buildings in hot and dry regions using sol-air temperature and ground temperature effects, Journal of Engineering, Design and Technology, Vol. 17, No. 3, pp. 613-628.
[4] Almutairi K. et al. (2021). Frontiers in Energy Research, Techno-Economic Investigation of using Solar Energy for Heating Swimming Pools in Buildings and Producing Hydrogen: A Case Study, doi.org/10.3389/fenrg.2021.680103.
[5] Jahangiri M. et al. (2019). An optimization of energy cost of clean hybrid solar-wind power plants in Iran, International Journal of Green Energy, Vol. 16, No.15, pp. 1422-1435.
[6] Jahangiri M. et al. (2019). Techno-econo-environmental optimal operation of grid-wind-solar electricity generation with hydrogen storage system for domestic scale, case study in Chad, International Journal of Hydrogen Energy, Vol. 44, No. 54, pp. 28613-28628.
[7] Moradi cheghamahi J. et al. (2019). Numerical solution of the Pulsatile, non-Newtonian and turbulent blood flow in a patient specific elastic carotid artery, International Journal of Mechanical Sciences, Vol. 150, pp. 393-403.
[8] Jahangiri M. et al. (2018). Comprehensive Evaluation of using Solar Water Heater on a Household Scale in Canada, Journal of Renewable Energy and Environment, Vol. 5, No. 1, pp. 35-42.
[9] Qiao Z.X. et al. (2021). Multi-frequency aerodynamic control of a yawed bluff body optimized with a genetic algorithm, Journal of Wind Engineering and Industrial Aerodynamics, 212104600.
[10] Minelli, G. et al. (2019). Active aerodynamic control of a separated flow using streamwise synthetic jets. Flow, Turbul. Combust, Vol. 103, No. 4, pp.1039–1055.
[11] Brunton S.L. et al. (2020). Machine learning for fluid mechanics, Annu. Rev. Fluid Mech, Vol. 52, pp. 477–508.
[12] Owan J. et al. (2013). Fifty years of wind engineering: prestige lectures from the sixth European and African conference of wind engineering, University of Birmingham.
[13] Tamura Y. (2009). Wind-induced damage to buildings and disaster risk reduction. In the seventh Asia-Pacific conference of wind engineering, Taipei, Taiwan.
[14] Andrianne T. (2012). Experimental and numerical investigation of the aeroelastic stability of bluff bodies. PhD thesis. Department of Aerospace and Mechanics. University of Liege.
[15] Minelli, G. et al. (2020). Upstream actuation for bluff-body wake control driven by a genetically inspired optimization, J. Fluid Mech, Vol. 893, pp. 1–28.
[16] Bonnavion, G. et al. (2019). Boat-tail effects on the global wake dynamics of a flat backed body with rectangular section, J. Fluid Struct, Vol. 89, pp. 61–71.
[17] Brook R.D. et al. (2004). Expert Panel on P, Prevention Science of the American Heart A. Air pollution and cardiovascular disease: a statement for healthcare professionals from the Expert Panel on Population and Prevention Science of the American Heart Association, Circulation, Vol. 109, pp. 2655–2671.
[18] Jahangiri M. et al. (2018). Electrification of a Tourist Village using Hybrid Renewable Energy Systems, Sarakhiyeh in Iran, Journal of solar energy research, Vol. 3, No. 3, pp. 201-211. [19] Jahangiri M. et al. (2018). Analysis of Standalone PV-Based Hybrid Systems for Power Generation in Rural Area, ICEEC01_166.
[20] Pahlavan S. et al. (2019), Assessment of PV-based CHP System: The Effect of Heat Recovery Factor and Fuel Type, Journal of Energy Management and Technology (JEMT), Vol. 3, No. 1, pp. 40-47.
[21] Li Z. et al. (2021). Review on pollutant dispersion in urban areas-part B: Local mitigation strategies, optimization framework, and evaluation theory. Build Environ, Vol. 198, 107890. [22] Gao NP. et al. (2009). The airborne transmission of infection between flats in high-rise residential buildings: particle simulation, Build Environ, Vol. 44, pp. 402–410.
[23] Allegrini J. et al. (2018). Simulations of local heat islands in Zurich with coupled CFD and building energy models, Urban Climate, Vol. 24, pp. 340–359.
[24] An K. et al. (2013). Sensitivity of inflow boundary conditions on downstream wind and turbulence profiles through building obstacles using a CFD approach. Journal of Wind Engineering and Industrial Aerodynamics, Vol. 115, pp 137–149.
[25] Antoniou N. et al. (2017). CFD and wind-tunnel analysis of outdoor ventilation in a real compact heterogeneous urban area: Evaluation using “air delay”, Building and Environment, Vol. 126, pp. 355–372.
[26] Bazdidi-Tehrani F. et al. (2013). Grid resolution assessment in large eddy simulation of dispersion around an isolated cubic building, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 121, pp. 1–15.
[27] Blocken B. et al. (2007a). CFD simulation of the atmospheric boundary layer: Wall function problems, Atmospheric Environment, Vol. 41, pp. 238–252.
[28] Tian ZF. et al. (2006). On the numerical study of contaminant particle concentration in indoor air flow, Building and Environment, Vol. 41, pp. 1504–1514.
[29] Ahmadi M. et al. (2019). RANS k-ω simulation of 2d turbulent natural convection in an enclosure with heating sources, IIUM Engineer Journal, Vol. 20, No. 1, pp. 229–244.
[30] He C. et al. (2017). A dynamic delayed detached-eddy simulation model for turbulent flows, Comput Fluids, Vol. 146, pp. 174-189.
[31] Wang M. et al. (2012). Advanced turbulence models for predicting particle transport in enclosed environments, Building and Environment, Vol. 47, pp. 40–49.
[32] Mirjalily SAA. (2021). Lambda shock behaviors of elliptic supersonic jets; a numerical analysis with modification of RANS turbulence model, Aerospace Science and Technology, Vol. 112, 106613.
[33] Baker CJ. (2007). Wind engineering-Past, present and future. Journal of Wind Engineering and Industrial Aerodynamics, Vol. 95, pp. 843-870.
[34] Meroney RN. (2016). Ten questions concerning hybrid computational/physical model simulation of wind flow in the built environment, Building and Environment, Vol. 96, pp. 12-21.
[35] Ahmadi M. (2017). Natural Convective Heat Transfer in a Porous Medium within a Two-Dimensional Enclosure, IIUM Engineering Journal, Vol. 18, No. 2, pp. 196–211.
[36] Tominaga Y. et al. (2016). Ten questions concerning modeling of near-field pollutant dispersion in the built environment, Building and Environment, Vol. 105, pp. 390-402.
[37] Meroney RN. et al. (2014). Virtual reality in wind engineering: the windy world within the computer, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 11, pp. 11-26.
[38] Jinglei X. et al. (2017). A dynamic hybrid RANS/LES approach based on the local flow structure, Int J Heat Fluid Flow, Vol. 67, pp. 250-260.
[39] Shur ML. et al. (2015). An enhanced version of DES with rapid transition from RANS to LES in separated flows, Flow Turbul Combust, Vol. 95, No. 4, pp. 709-737.
[40] Mockett C. et al. (2017). Go4Hybrid: Grey Area Mitigation for Hybrid RANS-LES Methods: Results of the 7th Framework Research Project Go4Hybrid, Funded by the European Union, 2013-2015. Berlin, CT: Springer-Verlag.
[41] Allmaras SR. et al. (2012). Modifications and clarifications for the implementation of the Spalart-Allmaras turbulence model, Paper presented at: Proceedings of the 7th International Conference on Computational Fluid Dynamics, pp.1-11.
[42] Tominaga Y. et al. (2010). Numerical simulation of dispersion around an isolated cubic building: model evaluation of RANS and LES, Building and Environment, Vol. 45, pp. 2231-2239.
[43] Gousseau P. et al. (2011). CFD simulation of pollutant dispersion around isolated buildings: on the role of convective and turbulent mass fluxes in the prediction accuracy, Journal of Hazardous Materials, Vol. 192, pp. 422.
[44] Bi A. (2006). Probability assessment of wind loads on a full-scale low-rise building, PhD thesis, Texas Tech University, United States.
[45] Patankar SV. (1980). Numerical Heat Transfer and Flow, McGraw-Hill, New York.
[46] Ferziger JH. et al. (1996). Computational Methods for Fluid Dynamics. Springer; Verlag, Berlin.
[47] Launder BE. et al. (1972). Lectures in Mathematical Models of Turbulence. Academic Press, London, England.
[48] You D. et al. (2007). A Dynamic Global-Coefficient Sub Grid-Scale Eddy-Viscosity Model for Large-Eddy Simulation in Complex Geometries, Phys Fluids, Vol. 19, No. 6, 065110–18.
[50] Moradi cheghamahi J. et al. (2019). Numerical solution of the Pulsatile, non-Newtonian and turbulent blood flow in a patient specific elastic carotid artery, International Journal of Mechanical Sciences, Vol. 150, pp. 393-403.
[51] Jahangiri M. et al. (2015). Numerical simulation of hemodynamic parameters of turbulent and pulsatile blood flow in flexible artery with single and double stenoses, Journal of Mechanical Science and Technology, Vol. 29, No. 8, pp. 3549-3560.
[52] Sharifzadeh B. et al. (2020). Computer modeling of pulsatile blood flow in elastic artery using a software program for application in biomedical engineering, Computer Methods and Programs in Biomedicine, Vol. 192, 105442.
[53] Sajjadi H. et al. (2017). Turbulent Indoor Airflow Simulation using Hybrid LES/RANS Model Utilizing Lattice Boltzmann Method, Comput Fluids, Vol. 150, pp.66–73.
[54] Ahmadi M. et al. (2020). Simulation of Pollutant Dispersion in Urban Street Canyons using Hybrid RANS-LES Method with Two-Phase Model, Computers and Fluids, Vol. 210, 104676.
[55] Ahmadi M. et al. (2020). CFD Simulation of Non-Newtonian Two-Phase Fluid Flow through a Channel with a Cavity, Thermal science, Vol. 24, No. 2B, pp.1045–54.
[56] Li XX. et al. (2008b). Physical modeling of flow field inside urban street canyons, J Appl Meteorol Climatol Vol. 47, No. 7, pp.2058–2067.
[57] Liu CH. et al. (2004). Large-eddy simulation of flow and pollutant transport in street canyons of different building-height-to-street-width ratios, J Appl Meteorol, Vol. 43, pp. 1410–1424.
[58] Dagnew AK. et al. (2010). LES evaluation of wind pressure on a standard tall building with a without a neighboring building, In the Fifth International Symposium on Computational Wind Engineering (CWE2010), Chapel Hill, North Carolina, USA, pp. 23-27.
[59] Dorneanu J. et al. (2016). Hirschberg, Tonal and silent wake modes of a square rod at incidence, ACTA Acustica United with Acustica, Vol. 102, No. 3, pp. 419-422.
[60] Knisely CW. (1990). Strouhal numbers of rectangular cylinders at incidence: a review and new data, Journal of Fluids and Structures, Vol. 4, No. 4, pp. 371-393.
[61] Goliger A.M. et al. (1988). Sensitivity of the caarc standard building model to geometric scale and turbulence, Journal of Wind Engineering and Industrial Aerodynamics, Vol. 31, No. 1, pp.105-123. | ||
|
آمار تعداد مشاهده مقاله: 1,439 تعداد دریافت فایل اصل مقاله: 484 |
||