[1] Updike D (1975) Thermal ratcheting under biaxial stress states. Nucl Eng Des 33(3): 387-397.

[2] Feigenbaum HP, Dugdale J, Dafalias YF, Kourousis KI, Plesek J (2012) Multiaxial ratcheting with advanced kinematic and directional distortional hardening rules. Int J Solid Struct 49(22): 3063-3076.

[3] Shen J, Chen H, Liu Y (2018) A new four-dimensional ratcheting boundary: Derivation and numerical validation. Eur J Mech A-Solid 71: 101-112.

[4] Abdalla H (2019) Effect of wall thinning on the shakedown interaction diagrams of 90-degree back-to-back bends subjected to simultaneous steady internal pressures and cyclic in plane bending moments. Thin-Wall Struct 144: 106228.

[5] Moslemi N, Zardian MG, Ayob A, Redzuan N, Rhee S (2019) Evaluation of sensitivity and calibration of the chaboche kinematic hardening model parameters for numerical ratcheting simulation. Appl Sci 9: 2578.

[6] Mehrabi H (2014) Experimental study of ratcheting influence on fatigue life of Ck45 in uniaxial cyclic loading. Modares Mechanical Engineering 13(10): 75-83.

[8] Groβ-Weege J, Weichert D (1992) Elastic-plastic shells under variable mechanical and thermal loads. Int J Mech Sci 34(11): 863-880.

[9] Megahed M (1981) Influence of hardening rule on the elasto-plastic behaviour of a simple structure under cyclic loading. Int J Mech Sci 23(3): 169-182.

[10] Auricchio F, Taylor RL (1995) Two material models for cyclic plasticity: nonlinear kinematic hardening and generalized plasticity. Int J Plast 11(1): 65-98.

[11] Abdel-Karim M, Ohno N (2000) Kinematic hardening model suitable for ratchetting with steady-state. Int J Plast 16(3-4): 225-240.

[12] Kang G, Kan Q (2007) Constitutive modeling for uniaxial time-dependent ratcheting of SS304 stainless steel. Mech Mater 39(5): 488-499.

[13] Yu D, Chen G, Yu W, Li D, Chen X (2012) Visco-plastic constitutive modeling on Ohno–Wang kinematic hardening rule for uniaxial ratcheting behavior of Z2CND18. 12N steel. Int J Plast 28(1): 88-101.

[14] Bradford R, Ure J, Chen H (2014) The Bree problem with different yield stresses on-load and off-load and application to creep ratcheting. Int J Pressure Vessels Piping 113: 32-39.

[15] Ziya-Shamami M, Babaei H, Mirzababaie Mostofi T, Khodarahmi H (2021) Experimental investigation of large plastic deformation of single-and multi-layered circular aluminum plates under repeated uniform impulsive loading. Journal of Solid and Fluid Mechanics 11(1): 123-137.

[16] Sagar V, Payne D (1975) Incremental collapse of thick-walled circular cylinders under steady axial tension and torsion loads and cyclic transient heating. J Mech Phys Solid 23(1): 39-53.

[17] Megahed MM (1990) Influence of hardening rule on prediction of cyclic plasticity in pressurized thin tubes subjected to cyclic push-pull. Int J Mech Sci 32(8): 635-652.

[18] Shiratori E, Ikegami K, Yoshida F (1979) Analysis of stress-strain relations by use of an anisotropic hardening plastic potential. J Mech Phys Solid 27(3): 213-229.

[19] Jiang Y, Kurath P (1996) Characteristics of the Armstrong-Frederick type plasticity models. Int J Plast 12(3): 387-415.

[20] Palgen L, Drucker D (1983) The structure of stress-strain relations in finite elasto-plasticity. Int J Solids Struc. 19(6): 519-531.

[21] Ohno N, Wang J (1993) Kinematic hardening rules with critical state of dynamic recovery, part I: formulation and basic features for ratchetting behavior. Int J Solids Struct 9(3): 375-390.

[22] Chen X, Jiao R, Kim K (2005) On the Ohno Wang kinematic hardening rules for multiaxial ratcheting modeling of medium carbon steel. Int J Plast 21: 161-184.

[23] Chaboche JL (1994) Modeling of ratchetting: evaluation of various approaches. Eur J Mech A-Soli. 13: 501-518.

[24] Chen X, Chen H, Zhao L (2019) Ratcheting behavior of pressurized corroded straight pipe subjected to cyclic bending. Thin-Wall Struct 145: 106410.

[25] Wada H, Igari T, Kitade S (1989) Prediction method for thermal ratcheting of a cylinder subjected to axially moving temperature distribution. Trans Jpn Soc Mech Eng A 55(512): 985-993.

[26] Angiolini M, Aiello G, Matheron P, Pilloni L, Giannuzzi G (2016) Thermal ratcheting of a P91 steel cylinder under an axial moving temperature distribution. J Nucl Mater 472: 215-226.

[27] Paul SK, Sivaprasad S, Dhar S, Tarafder S (2010) Ratcheting and low cycle fatigue behavior of SA333 steel and their life prediction. J Nucl Mater 401(1-3): 17-24.

[28] Hassan T, Kyriakides S (1992) Ratcheting in cyclic plasticity, part I: Uniaxial behavior. Int J Plast 8(1): 91-116.

[29] Bree J (1967) Elastic-plastic behaviour of thin tubes subjected to internal pressure and intermittent high-heat fluxes with application to fast-nuclear-reactor fuel elements. J Strain Anal 2(3): 226-238.

[30] Resapu RR, Perumahanthi LR (2021) Numerical study of bilinear isotropic & kinematic elastic–plastic response under cyclic loading. Mater Today Proc 39: 1647-1654.

[31] Sahoo P, Chatterjee B, Adhikary D (2010) Finite element based elastic-plastic contact behavior of a sphere against a rigid flat-effect of strain hardening. Int J Eng Technol 2(1): 1-6.

[32] Damadam M, Moheimani R, Dalir H (2018) Bree's diagram of a functionally graded thick-walled cylinder under thermo-mechanical loading considering nonlinear kinematic hardening. Case Stud Therm Eng 12: 644-654.

[33] Ure J, Chen H, Li T, Chen W, Tipping D, Mackenzie D (2011) A direct method for the evaluation of lower and upper bound ratchet limits. Procedia Eng 10: 356-361.

[34] Gardner L, Cruise RB, Sok CP, Krishnan K Ministro Dos Santos J (2007) Life-cycle costing of metallic structures. J Inst Civ Eng-Eng Sustainability, Thomas Telford Ltd 167-177.

[35] Bree J (1989) Plastic deformation of a closed tube due to interaction of pressure stresses and cyclic thermal stresses. Int J Mech Sci 31(11-12): 865-892.

[36] Ezzati M, Naghipour M, Zeinoddini M, Zandi A, Elyasi M (2021) Strain ratcheting failure of dented steel submarine pipes under combined internal pressure and asymmetric inelastic cycling. Ocean Eng 219: 108336.

[37] Cho NK, Chen H (2018) Shakedown, ratchet, and limit analyses of 90 back-to-back pipe bends under cyclic in-plane opening bending and steady internal pressure. Eur J Mech A-Solid 67: 231-242.