Cavity Growth in Underground Coal Gasification Method by Considering Cleat Length and Inclination of Coal with Elasto-Brittle Behavior | ||
| Journal of Mining and Environment | ||
| مقاله 18، دوره 13، شماره 2، تیر 2022، صفحه 607-625 اصل مقاله (10.67 M) | ||
| نوع مقاله: Original Research Paper | ||
| شناسه دیجیتال (DOI): 10.22044/jme.2022.11906.2183 | ||
| نویسندگان | ||
| M.R. Shahbazi1؛ M. Najafi* 1؛ M. Fatehi Marji1؛ A. Abdollahipour2 | ||
| 1Department of Mining and Metallurgical Engineering, Yazd University, Yazd, Iran | ||
| 2School of Mining Engineering, College of Engineering, University of Tehran, Tehran, Iran | ||
| چکیده | ||
| The in-situ coal is converted to the synthetic gas in the process of underground coal gasification (UCG). In order to increase the rate of in-situ coal combustion in the UCG process, the contact surfaces between the steam, heat, and coal fractures should be raised. Therefore, the number of secondary cracks should be increased by raising the heat and existing steam pressure during the process. This paper emphasises on the secondary crack growth mechanism of the pre-existing cracks in the coal samples under different loading conditions. Different geometric specifications such as the length of the pre-existing cracks (coal cleats) and their inclinations are considered. The numerical modeling results elucidate that the first crack growths are the wing cracks (also called the primary or tensile cracks) formed due to unbonding the tensile bonds between the particles in the assembly. Ultimately, these cracks may lead to the cleat coalescences. On the other hand, the secondary or shear cracks in the form of co-planar and oblique cracks may also be produced during the process of crack growth in the assembly. These cracks are formed due to the shear forces induced between the particles as the initial cleat length is increased and exceed the dimension of coal blocks. The cavity growth rate increases as the secondary cracks grow faster in the coal blocks. In order to achieve the optimum conditions, it is also observed that the best inclination angle of the initial coal cleat changes between 30 to 45 degrees with respect to the horizon for the coal samples with the elasto-brittle behavior. | ||
| کلیدواژهها | ||
| UCG method؛ cavity growth rate؛ crack propagation؛ cleat length and inclination؛ parallel bonded particle model | ||
| مراجع | ||
|
[1]. Couch, G.R. (2009). Underground Coal Gasification. London, UK: IEA Clean Coal Centre.
[2]. Saulov, D.N., Ovid, A.P. and Klimenko, A.Y. (2010). Flame propagation in a gasification channel. Energy, 35, 1264–73.
[3]. Blinderman, M.S., Saulov, D.N., and Klimenko, A.Y. (2008). Forward and reverse combustion linking in underground coal gasification. Energy. 33 (3): 446-454.
[4]. Su, F., Itakura, K., Deguchi, G. and Ohga, K. (2016). Monitoring of coal fracturing in underground coal gasification by acoustic emission techniques. Applied Energy, 189, 142-156.
[5]. Javed, S.B., Uppal, A.A., Bhatti, A.I., and Samar, R. (2019). Prediction and parametric analysis of cavity growth for the underground coal gasification project Thar. Energy, 172, 1277-1290.
[6]. Gao, W., Zagorscak, R. and Thomas, H, R. (2021). Insights into solid-gas conversion and cavity growth during Underground Coal Gasification (UCG) through Thermo-Hydraulic-Chemical (THC) modelling. International Journal of Coal Geology, 237, 103711.
[7]. Shahbazi, M., Najafi, M. and Marji, M.F. (2018). On the mitigating environmental aspects of a vertical well in underground coal gasification method, Mitigation and Adaptation Strategies for Global Change, 24, 373–398.
[8]. Marji, M.F. (1997). Modelling of cracks in rock fragmentation with a higher order displacement discontinuity method. PhD Thesis in Mining Engineering (Rock Mechanics), METU, Ankara, Turkey.
[9]. Haeri, H., Sarfarazi, V., Ebneabbasi, P., Shahbazian, A. and Marji, M.F. (2020). XFEM and experimental simulation of failure mechanism of non-persistent joints in mortar under compression. Construction and Building Materials, 236, 117500.
[10]. Haeri, H., Sarfarazi, V., Zhu, Z., Marji, M.F. and Masoumi, A. (2019). Investigation of shear behavior of soil-concrete interface. Smart Structures and Systems. 23 (1): 81-90.
[11]. Haeri, H., Khaloo, A.R., Shahriar, K., Marji, M.F. and Moaref Vand, P. (2015). A boundary element analysis of crack-propagation mechanism of micro-cracks in rock-like specimens under a uniform normal tension. Journal of Mining and Environment. 6 (1): 73-93.
[12]. Sarfarazi, V., Haeri, H., Marji, M.F. and Zhu, Z. (2017). Fracture mechanism of Brazilian discs with multiple parallel notches using PFC2D. Periodica Polytechnica Civil Engineering. 61 (4): 653-66.
[13]. Zhao, Y.X., Zhao, G.F. and Jiang, Y.D. (2013). Experimental and numerical modelling investigation on fracturing in coal under impact loads. International Journal of Fracture, 183, 63–80.
[14]. Xiangchun, L., Chao, W., Caihong, Z. and Hua, Y. (2012). The propagation speed of the cracks in coal body containing gas. Safety Science. 50 (4): 914-917.
[15]. Wang, C., Zhang, C., Li, T. and Zheng, C. (2019). Numerical investigation of the mechanical properties of coal masses with T-junctions cleat networks under uniaxial compression. International Journal of Coal Geology, 202, 128-146.
[16]. Wu, P.F., Liang, W.G., Li, Z.G., Cao, M.T. and Yang, J.F. (2016). Investigations on mechanical properties and crack propagation characteristics of coal and sandy mudstone using three experimental methods. Rock Mechanics and Rock Engineering, 50, 215-223.
[17]. Li, L., Yan, S., Liu, Q. and Yu, L. (2018). Micro- and macroscopic study of crack propagation in coal: theoretical and experimental results and engineering practice. Journal of Geophysics and Engineering. 15 (4): 1706-1718.
[18]. Yin, G.Z., Gao, D.F. and Pi, W.L. (2003). CT real-time analysis of damage evolution of coal under uniaxial compression. J. Chongqing Univ, 26, 96–100.
[19]. Zhang, X.P. and Wong, L.N.Y. (2012). Crack Initiation, Propagation and Coalescence in Rock-Like Material Containing Two Flaws: A Numerical Study Based on Bonded-Particle Model Approach. Rock Mechanics and Rock Engineering, 46,1001–1021.
[20]. Xie, Y., Cao, P., Liu, J. and Dong, L. (2016). Influence of crack surface friction on crack initiation and propagation: A numerical investigation based on extended finite element method. Computers and Geotechnics, 74, 1-14.
[21]. Yue, Z., Peng, L., Yue, X., Wang, J. and Lu C., (2020). Experimental study on the dynamic coalescence of two-crack granite specimens under high loading rate. Engineering Fracture Mechanics 237, 107254.
[22]. Lin, Q., Cao, P., Wen, G., Meng, J., Cao, R. and Zhao, Z. (2021). Crack coalescence in rock-like specimens with two dissimilar layers and pre-existing double parallel joints under uniaxial compression. International Journal of Rock Mechanics & Mining Sciences, 139, 104621.
[23]. Sharafisafa, M. and Nazem, M. (2014). Application of the distinct element method and the extended finite element method in modelling cracks and coalescence in brittle materials. Computational Materials Science, 91, 102–121.
[24]. Marji, F.M. (2014). Numerical analysis of quasi-static crack branching in brittle solids by a modified displacement discontinuity method. International Journal of Solids and Structures. 51 (9): 1716-1736.
[25]. Reyes, O. and Einstein, H.H. (1991). Failure mechanism of fractured rock—a fracture coalescence model. Proceedings of the seventh international congress on rock mechanics, Aachen, Germany.
[26]. Vaughan, H. (1998). Crack propagation and the principle-tensile-stress criterion for mixed-mode loading. Engineering Fracture Mechanics. 59 (3): 393-397.
[27]. Shen, B. and Stephansson, O. (1994). Modification of the G-criterion for crack propagation subjected to compression. Engineering Fracture Mechanics. 47 (2): 177–189.
[28]. Bakhshi, E., Rasouli, V., Ghorbani, A., Marji, F.M., Damjanac, B. and Wan, X. (2019), Lattice Numerical Simulations of Lab-Scale Hydraulic Fracture and Natural Interface Interaction, Rock Mechanics and Rock Engineering. 52 (5): 1315-1337.
[29]. Lak, M., Marji, F.M., Bafghi, A.Y. and abollahipour, A. (2018). Discrete element modeling of explosion-induced fracture extension in jointed rock masses. Journal of Mining and Environment. 10 (1): 125-138.
[30]. Itasca consulting group, Inc. PFC 2D Version 6.00. (www.itascacg.com).
[31]. Zhang, B., Bicanic, N., Pearce, C.J. and Phillips, D.V. (2002). Relationship between brittleness and moisture loss of concrete exposed to high temperatures. Cement and Concrete Research, 32, 363-371. | ||
|
آمار تعداد مشاهده مقاله: 696 تعداد دریافت فایل اصل مقاله: 757 |
||