Failure Mechanism of Rock Pillar Containing Two Edge Notches: Experimental Test and Numerical Simulation | ||
| Journal of Mining and Environment | ||
| مقاله 15، دوره 14، شماره 3، مهر 2023، صفحه 961-971 اصل مقاله (4.14 M) | ||
| نوع مقاله: Original Research Paper | ||
| شناسه دیجیتال (DOI): 10.22044/jme.2023.12909.2341 | ||
| نویسندگان | ||
| Amir Rezaei؛ Vahab Sarfarazi* ؛ Nima Babanouri؛ Mohammad Omidi manesh؛ Shirin Jahanmiri | ||
| Department of Mining Engineering, Hamedan University of Technology, Hamedan, Iran | ||
| چکیده | ||
| Non-persistent joints are geologic occurrences in rocks that weaken pillars because they are present within them. Using practical tests and numerical models, it has been determined how edge notches affect the way pillars break. Gypsum samples that are notched and have dimensions of 70 mm by 70 mm by 50 mm are created. Gypsum's Young modulus, Poisson ratio, compressive strength, and tensile strength are 5.5 GPa, 0.27, 8 MPa, and 1.1 MPa, respectively. 10-, 20-, and 30-degree notch angles are used. The model receives an axial stress at a rate of 0.05 mm/min. On a rock pillar, numerical simulation is carried out concurrently with an experimental test. The findings indicate that the joint angle is mostly responsible for the failure process. The fracture pattern and failure mechanism of the pillars are connected to the compressive strengths of the specimens. At the notch points, two significant splitting tensile fractures spread vertically until coalescing with the top and lower boundaries of the models. On the left and right sides of the pillar, two rock columns are also taken out. The overall number of cracks rises as sample loading increases. The model's deformation at the start of loading reflect a linear elastic behavior, and the number of fractures steadily grows. When the number of cracks increases, the curve becomes non-linear, and the force being applied peaks. When the sample can no longer tolerate the applied force, a dramatic stress decrease occurs. The macro-failure over the whole model is what leads to the greater stress decrease following the peak load. In actuality, the reduced stress reduction is accompanied by more overall fractures. Similar findings are shown in both the experimental testing and numerical modeling. | ||
| کلیدواژهها | ||
| Rock pillar؛ edge notch؛ experimental test؛ PFC | ||
| مراجع | ||
|
[1]. Jaeger, J.C. and Cook N.G.W. (1979). Fundamentals of Rock Mechanics, 3rd Ed. NewYork, Chapman and Hall.
[2]. Esterhuizen, G.S. (2006). An evaluation of the strength of slender pillars. Transactions of Society for Mining, Metallurgy, and Exploration, Inc. Vol. 320. Littleton, CO: Society for Mining, Metallurgy, and Exploration, Inc, pp, 69–76.
[3]. Chiu, C.C. Weng, M.C. and Huang, T.H. (2016). Modeling rock joint behavior using a rough-joint model. International Journal of Rock Mechanics and Mining Sciences, 89, 14-25
[4]. Hadjigeorgiou, J., Esmaieli, K. and Grenon, M. (2009). Stability analysis of vertical excavations in hard rock by integrating a fracture system into a PFC model. Tunneling and Underground Space Technology, 24(3), 296-308
[5]. Qin, Z., Fu, H. and Chen, X.X. (2019). A study on altered granite meso-damage mechanisms due to water invasion-water loss cycles. Environmental Earth Sciences. 78 (14): 428, 1-10.
[6]. Wang, X. and Tian, L.G. (2018). Mechanical and crack evolution characteristics of coal–rock under different fracture-hole conditions: a numerical study based on particle flow code. Environmental Earth Sciences. 77 (8): 297, 1-10.
[7]. Wong, L.N.Y., Einstein, H.H. (2009). Crack coalescence in molded gypsum and carrara marble: part 1. macroscopic observations and interpretation. Rock Mechanics and Rock Engineering, 42, 475-511.
[8]. Zhou, X.P., Cheng, H. and Feng, Y.F. (2014). An experimental study of crack coalescence behavior in rock-like materials containing multiple flaws under uniaxial compression. Rock Mechanics and Rock Engineering, 47, 1961-1986
[9]. Shen, B., Stephansson, O., Einstein, H.H. and Ghahreman, B. (1995). Coalescence of fractures under shear stresses in experiments. Journal of Geophysical Research, 100, 5975-5990.
[10]. Mughieda, O. and Alzo'ubi, A.K. (2004). Fracture mechanisms of offset rock joints-a laboratory investigation. Geotechnical and Geological Engineering, 22, 545-562.
[11]. Cheng, Y., Wong, L. and Zou, C.J. (2015). Experimental study on the formation of faults from en -echelon fractures in carrara marble. Engineering Geology, 195,312-326.
[12]. Chiu, C.C., Weng, M.C., and Huang, T.H. (2016). Modeling rock joint behavior using a rough-joint model. International Journal of Rock Mechanics and Mining Sciences, 89, 14-25.
[13]. Zhang, B., Li, S.C., Zhou, F., Yang, X.Y., Xia, K.W., Liu, J.Y., Guo, S. and Wang, S.G. (2019). The coalescence and strength of rock-like materials containing two aligned X-type flaws under uniaxial compression. Geomechanics and Engineering, 17, 47-56.
[14]. Wang, X., Yuan, W., Yan, Y.T., and Zhang, X. (2020). Scale effect of mechanical properties of jointed rock mass: a numerical study based on particle flow code. Geomechanics and Engineering. 21 (3): 259-268.
[15]. Chai, S.B., Wang, H., Yu, L.Y., Shi, J.H. and Abi, E.D. (2020). Experimental Study on Static and Dynamic Compression Mechanical Properties of Filled Rock Joints. Latin American Journal of Solids and Structures. 17 (3): 264.
[16]. Chen, C.S., Pan, E. and Amadei, B. (1998). Fracture mechanics analysis of cracked discs of anisotropic rock using the boundary element method. International Journal of Rock Mechanics and Mining Science. 35: 195-218.
[17]. Feng, X.T., Pan, P.Z. and Zhou, H. (2006). Simulation of the rock micro-fracturing process under uniaxial compression using an elasto-plastic cellular automaton. International Journal of Rock Mechanics and Mining Science, 43: 1091-1108.
[18]. Ning, Y., Yang, J., An, X. and Ma, G. (2011). Modelling rock fracturing and blast-induced rock mass failure via advanced discretisation within the discontinuous deformation analysis framework. Computers and Geotechnics. 38: 40-49.
[19]. Sarfarazi, V. and Haeri, H. (2022). PFC simulation of Brazilian tensile strength test in geomaterials’ specimens with T-shaped non-persistent joints. Journal of Mining and Environment 13 (4): 1189-1209.
[20]. Potyondy, D.O. and Cundall, P.A. (2004). A bonded-particle model for rock. International Journal of Rock Mechanics and Mining Science, 41, 1329-1364.
[21]. Wu, Z.J. and Wong, L.N.Y. (2013). Elastic-plastic cracking analysis for brittle-ductile rocks using manifold method. International Journal of Fracture, 180, 71-91.
[22]. Yaylaci, M. and Birinci, A. (2013). The receding contact problem of two elastic layers supported by two elastic quarter planes. Structural Engineering and Mechanics. 48 (2): 241-255.
[23]. Yaylaci, M. Öner, E. and Birinci, A. (2014). Comparison between Analytical and ANSYS Calculations for a Receding contact Problem. Journal of Engineering Mechanics. 140 (9): 56-66.[24]. Yaylacı, M. and Avcar, M. (2020). Finite element modeling of contact between an elastic layer and two elastic quarter planes. Computers and Concrete, Vol. 26, No. 2 (2020): 107-114.
[25]. Yaylacı, M. Terzi, C. and Avcar, M. (2019). Numerical analysis of the receding contact problem of two bonded layers resting on an elastic half plane. Structural Engineering and Mechanics. 72 (6).
[26] Nehrii, S., Nehrii, T., Zolotarova, O. and Volkov, S. (2021). Investigation of the geomechanical state of soft adjoining rocks under protective constructions. Rudarsko-geološko-Naftni Zbornik (The Mining-Geological-Petroleum Bulletin). 36 (4): 61-71.
[27]. Nehrii, S., Nehrii, T., Kultaev, S. and Zolotarova, O. (2020). Providing resistance of protection means on the soft adjoining rocks. E3S Web Conf., 168, 00033. DOI: 10.1051/e3sconf/202016800033.
[28]. Zhang, X.P. and Wong, L.N.Y. (2012). Cracking processes in rock-like material containing a single flaw under uniaxial compression: a numerical study based on parallel bonded-particle model approach. Rock Mechanics and Rock Engineering, 45, 711-737.
[29]. Fakhimi, A., Carvalho, F., Ishida, T. and Labuz, J.F. (2002). Simulation of failure around a circular opening in rock. International Journal of Rock Mechanics and Mining Science. 39: 507-515.
[30]. Lee, H. and Jeon, S. (2011). An experimental and numerical study of fracture coalescence in pre cracked specimens under uniaxial compression. International Journal of Solids and Structures. 48: 979-999.
[31]. Khazaei, C., Hazzard, J. and Chalaturnyk, R. (2015). Damage quantification of intact rocks using acoustic emission energies recorded during uniaxial compression test and discrete element modeling. Computers and Geotechnics. 67: 94-102.
[32]. Jin, J., Cao, P., Chen, Y., Pu, C.Z., Mao, D.W. and Fan, X. (2017). Influence of single flaw on the failure process and energy mechanics of rock-like material. Computers and Geotechnics. 86: 150-162.
[33]. Potyondy, D. O. (2015). The bonded-particle model as a tool for rock mechanics research and application: Current trends and future directions. Geosystem Engineering. 18 (1): 1–28.
[34]. Ghazvinian, A., Sarfarazi, V., Schubert, W. and Blumel, M. (2012). A study of the failure mechanism of planar non-persistent open joints using PFC2D. Rock Mechanics and Rock Engineering. 45 (5): 677–693.
[35]. King, M.S. and Pettitt, W.S. (2012). Young, Acoustic emissions associated with the formation of fracture sets in sandstone under polyaxial stress conditions Geophys. Prospect. 60 (2012): 93–102, https://doi.org/10.1111/j.1365. | ||
|
آمار تعداد مشاهده مقاله: 203 تعداد دریافت فایل اصل مقاله: 425 |
||