Andrews, P.G. and Barsanti, B.J. (2008). Results of the Radius Factor Stability Assessment Method for Design and Pillar Extraction at the Conqueror Mine, St Ives Gold Mine. SHIRMS

Azadmehr, A., Jalali, S. E., Pour Rahimian, Y., (2019). An application of Rock engineering System for assessment of the Rock Mass Fragmentation: A hybrid approach and case study, Rock Mechanics and Rock Engineering

Azadmehr, A., Jalali, S. E., Pour Rahimian, Y., (2017). Ranking of influencing factors on rock mass fragmentation in block caving, MPES 2017, Lulea, Sweden

Germain, P and Hadjigeorgiou, J. (1998). Influence of stope geometry on mining performance, Proceedings of 100th Annual General Meeting, CIM, Vancouver, B.C., Canada

Henning, J.G.  and Mitri, H.S. (2006).  Numerical modelling of ore dilution in blasthole stoping. Int. J. Rock Mech. Min. 44, pp. 692–703.

Laubscher, D.H. (1977). Geomechanics classification of jointed rock masses - mining applications. Transactions, Institute of Mining and Metallurgy, Section A, Vol. 86, pp. A1-8

Laubscher, D. H. (2000). A practical manual on block caving. Julius Kruttschnitt Mineral Research Centre, Brisbane.

McMahon, B. K., & Kendrick, R. F. (1969). Predicting the Block Caving Behavior of Ore Bodies. New york: AIME.

Milne, D.M., Pakalnis, R.C.  and Felderer, M. (1996). Surface geometry assessment for open stope dsign, Proceedings of North America Rock Mechanics Symposium, Kingston,

Milne, D.M. (1997) Underground Design and Deformation based on surface geometry. PhD thesis, The University of British Columbia.

Milne, D.M. and Pakalnis, R. (1997) Theory behind empirical design techniques. Proceedings 12th colloque en controle de terrain, Assoc. Min, Québe

Mortazavi, A & Osserbay, B. (2021). The Consolidated Mathews Stability Graph for Open Stope Design. School of Mining & Geosciences, Nazarbayev University

Mahtab, M. A., & Dixon, J. D. (1976). Influence of rock fractures and block boundary weakening on cavability. Trans Soc Min Eng AIME, 260(1), 6-12.

Mathews, K., Hoek, E., Wyllie, D., & Steward, S. (1981). Prediction of stable excavation spans for mining at depths below 1000 meters in hard rock mines. CANMET report DSS, Serial No. 0SQ80-00, Vol. 81

Mawdesley, C.A. (2002). Predicting rock mass cavability in block caving mines, PhD thesis, The University of Queensland, Brisbane, Australia.

Mawdesley, C. A.  Trueman,  R. and W. Whiten, (2001). Extending the Mathews stability graph for open-stope design, Trans. Institut. Min. Metallurg. (Section A: Mining Indust.) 110, pp. A27–A39.

Nickson, S.D. (1992) Cable support guidelines for underground hard rock mine operations. Master’s Thesis, University of British Columbia.

Potvin, Y. (1988). Empirical open stope design in Canada (Doctoral dissertation, University of British Columbia).

Potvin, Y., & Hudyma, M. (2000). Open stope mining in Canada. Proceedings of the MassMin2000, Brisbane. Carlton: AusIMM, 661e74.

Rafiee, R., Ataei, M., Khalokakaei, R., Jalali, S. E., & Sereshki, F. (2014). Determination and Assessment of Parameters Influencing Rock Mass Caveability in Block Caving Mines Using the Probabilistic Rock Engineering Syste. International Journal of Rock Mechanics and Rock Engineering.

Stewart, S. B. V., & Forsyth, W. W. (1995). The Mathew's method for open stope design. CIM bulletin, 88(992), 45-53.

Sainsbury, B. (2012). A model for cave propagation and subsidence assessment in jointed rock masses. University of South Wales

Suorineni. F.T. (2010). The stability graph after three decades in use: Experiences and the way forward. International Journal of Mining, Reclamation and Environment 24, 307–339

Suorineni, F T, Tannant, D D and Kaiser, P K, 2001. Likelihood statistic for interpretation of the stability graph for open stope design, International Journal Rock Mechanics and Mineral Science, 36(7):891–906.

Suorineni. F.T, & Madenova. Y (2022). The qualitative stability graph for open stope design- recent developments. Paper presented at the 56th U.S. Rock Mechanics/Geomechanics Symposium, Santa Fe, New Mexico, USA, June 2022.

Shacker, D. (2019). Research into the interpretation of deformation measured by extensmeters. . M.A.Sc. thesis, University of Saskatchewan, Canada

Trueman, R., Mikula, P., Mawdesley, C., & Harries, N. (2000). Experience in Australia with the application of the Mathews' method for open stope design. CIM bulletin, 93(1036), 162-167.

Vera, S. G. (1981). Caving at Climax. In D. Stewart, SME Mining Engineering Handbook, 157-176. New York: Society of Mining Engineers of the American Institute of Mining, Metallurgical, and Petroleum Engineers.