[1] Gore, A. S., & Patil, N. G. (2018). Wire electro discharge machining of metal matrix composites: A review. Procedia Manuf., 20, 41-52.

[2] Velmurugan, C., Subramanian, R., Thirugnanam, S., & Ananadavel, B. (2011). Experimental investigations on machining characteristics of Al 6061 hybrid metal matrix composites processed by electrical discharge machining. Inter. J. Eng. Sci. Technol. 3(8), 87-101.

[3]  Z. Zhong and N. P. Hung (2002) "Grinding of alumina/aluminum composites," J. Mater. Process. Technol. vol. 123, no. 1, pp. 13-17.

[4] A. Srivastava, Sunil Kumar Yadav and D.K. Singh (2020) Modeling and Optimization of Electric Discharge Machining Process Parameters in machining of Al 6061/SiCp Metal Matrix Composite, Materials Today: Proceedings, https://doi.org/10.1016/j.matpr.11.235

[6] Hourmand, M., Farahany, S., Sarhan, A. A., & Noordin, M. Y. (2015). Investigating the electrical discharge machining (EDM) parameter effects on Al-Mg 2 Si metal matrix composite (MMC) for high material removal rate (MRR) and less EWR–RSM approach. Int. J. Adv. Manuf. Technol. 77, 831-838.

[8] Lakshmanan, P., Kumanan, G., Arunkumar, L., & Amith, S. C. (2021). Experimental investigations of material removal rate on Mg/SiCp-flyash hybrid metal matrix composites by electrical discharge machining. Mater. Today: Proceedings, 46, 986-990.

[9]  Singh, B., Kumar, J., & Kumar, S. (2016). Investigation of the tool wear rate in tungsten powder-mixed electric discharge machining of AA6061/10% SiCp composite. Mater. Manuf. Process. 31(4), 456-466.

[10] Muniamuthu, S., & Rathinasuriyan, C. (2023). Effect of dielectric medium on electro-discharge machining of aluminium metal matrix composites. Mater. Today: Proceedings.

[11] Vahdati, M. (2020). 'Statistical analysis and optimization of parameters affecting the hardness of butt joint cross-section of Al7075 produced by FSW and SFSW using RSM and desirability approach', J. Fluid Mech. 10(4), pp. 165-180. doi: 10.22044/jsfm.2020.9476.3136

[12] Ponappa, K., Aravindan, S., Rao, P. V., Ramkumar, J., & Gupta, M. (2010). The effect of process parameters on machining of magnesium nano alumina composites through EDM. Int. J. Adv. Manuf. Technol. 46, 1035-1042.

[13] Mostafapor, Amir, and Hossein Vahedi (2019) "Wire electrical discharge machining of AZ91 magnesium alloy; investigation of effect of process input parameters on performance characteristics." Mater. Res. Express. 1.1: 015005. https://doi.org/10.1088/2631-8695/ab26c8

[14] Vahdati, M., Moradi, M. (2019). 'Statistical Analysis of Parameters Affecting the Mechanical Properties of Surface Composite Al7075/Al2O3 Produced by Friction Stir Processing Using Response Surface Methodology', J. Fluid Mech. 9(3), pp. 81-94. doi: 10.22044/jsfm.2019.8826.2997

[15] Douglas C. Montgomery (2011) Design and analysis of experiments, 7th Edittion, pp. 457-460, New York: John Wiley and Son.

[16] Hsieh CS, Zhu H, Wei TY, Chung ZJ, Yang WD, Ling YH (2008) Applying the experimental statistical method to deal the preparatory conditions of nanometric-sized TiO2 powders from a two-emulsion process, J. Eur. Ceram. Soc. Vol. 28, pp. 1177–1183.

[17] Hou TH, Su CH, Liu WL (2007) Parameters optimization of a nano-particle wet milling process using the taguchi method response surface method and geneticalgorithm, journal of Powder Technol, Vol. 173, pp. 153-162.

[18] A. Nekahi, K. Dehghani (2010) Modeling the thermo mechanical effects on baking behavior of low carbon steels using response surface methodology, J. Mater. Sci. Vol. 31, pp. 3845–3851.