[2] Zamani P, Farhangdoost K (2020) On the Influence of riveting process parameters on fatigue life of riveted lap joint. J. Appl. Comput. Mech. 6(2):248-58.

[3] Kemmenoe DJ, Theisen EA, Baker SP (2022) Strength of 444 stainless steel single-lap joints brazed with Ni-based metallic glass foils for corrosive environments. Metall. Mater. Trans. A 53(4):1407-18.

[4] Haran-Nogueira A, Kasaei MM, Akhavan-Safar A, Carbas RJ, Marques EA, da Silva LF (2023) Failure analysis of hybrid bonded-hole hemmed joints for dissimilar materials. Thin-Walled Struct. 189:110907.

[5] Chaturvedi M (2020) Welding and joining of aerospace materials. Woodhead publishing.

[6] Minea AA (2016) Book Review: Introduction to Brazing Technology. The Annals of" Dunarea de Jos" University of Galati. Fascicle XII: Welding Equipment and Technology 27:5.

[7] Way M, Willingham J, Goodall R (2020) Brazing filler metals. Int. Mater. Rev. 65(5):257-285.

 [8] Klotz UE, Liu C, Khalid FA, Elsener HR (2008) Influence of brazing parameters and alloy composition on interface morphology of brazed diamond. Mater. Sci. Eng. 495(1-2): 265-270.

 [9] Kamal A, Shukla AK, Shinde VM, Rajasekhar BV (2023) Microstructure and mechanical properties of C/SiC-niobium alloy (C103) joint brazed with TiCuAg alloy for aerospace applications. Ceram. Int.

 [10] Hongjie H, Guangmin Sh, Mingcan L, and Yingjun J (2018) Dynamic behaviors of 0Cr18Ni0Ti temperatures stainless steel welded joints at elevated and high strain rates. RARE METAL. MAT. ENG. 47(8): 2290-2297.

 [11] Davoodi Jamaloei A, Khorram A, Jafari A (2017) Characterization of microstructure and mechanical properties of dissimilar TLP bonding between IN718/IN600 with BNi-2 interlayer. J. Manuf. Process. 29: 447–457.

 [12] رضا سلطانی طاشی، سید علی اصغر اکبری موسوی (1389) شکست پذیری اتصال غیرمشابه لحیم کاری سخت تحت خلاء Ti-6Al-4V به فولاد زنگ‌نزن 316L با استفاده از فلز پرکننده AgCuZn. یازدهمین کنفرانس ملی جوش و بازرسی، تهران.

[13] Li Y, Feng J, Peng H (2009) Mechanical response of the TiAl/steel brazed joint under impact load. J Mater Sci 44: 3077–3081.

[14] Yaning L, Xinting K, Jian W, Huiping T (2018) Bonding Characterization Between 316L and Porous Stainless Steel Pipes by Vacuum Brazing. RARE METAL. MAT. ENG. 47(2): 0474-0478.

[15] Sudmeyer I, Hettesheimer T, Rohde M (2010) On the shear strength of laser brazed SiC–steel joints: Effects of braze metal fillers and surface patterning. Ceram. Int. 36(3): 1083–1090.

[17] Dong k, Kong J (2019) A high-strength vacuum-brazed TiAl/Ni joint at room temperature and high temperature with an amorphous foil Zr-Al-Ni-Co filler metal. J. Manuf. Process. 44: 389–396.

[18] Du Y, Zhang J, Li J, Wang F, Ding Y, Xiong J, Guo W (2023) Microstructure evolution and mechanical properties of Ti2AlNb/TC17 joints brazed with Ti–Zr–Cu–Ni filler metal. J. Vac. 215: 112365.

[19] American Welding Society: AWS C3.2 Standard Method for Evaluating the Strength of Brazed Joints, American Welding Society, Miami, FL, 2019, pp. 1–17.

[20] Montgomery DC (2017) Design and analysis of experiments. John wiley & sons.

[21] Eriksson L, Johansson E, Kettaneh-Wold N, Wikström C, Wold S (2000) Design of experiments. Principles and Applications, Learn ways AB, Stockholm.

[22] Li Y, Feng J, Peng H, Hua Z (2009) Mechanical response of the TiAl/steel brazed joint under impact load. J. Mater. Sci. 44:3077-81.

[23] Lugscheider E, Krappitz H (1986) The influence of brazing conditions on the impact strength of high-temperature brazed joints. Weld. J. 65(10): 261.

[24] Cai YS, Liu RC, Zhu ZW, Cui YY, Yang R (2017) Effect of brazing temperature and brazing time on the microstructure and tensile strength of TiAl-based alloy joints with Ti-Zr-Cu-Ni amorphous alloy as filler metal. Intermetallics 91:35-44.

[25] Zaharinie T, Yusof F, Hamdi M, Ariga T, Moshwan R (2014) Effect of brazing temperature on the shear strength of Inconel 600 joint. Int. J. Adv. Manuf. Technol. 73: 1133-40.

[26] Lee YW, Kim JH, Song YS, Seok CS (2007) Mechanical strength and microstructural characterization of SUS304 brazed joints with BNi-2 filler metal: influence of brazing temperature and time. Solid State Phenomena 124: 1673-6.

[27] Kawakatsu I, Osawa T, Saito H (1979) Brazed joint strength of stainless steel with nickel base filler metals. J. JPN. I. MET. MATER. 43(11): 1001-7.

 

[28] Fazeli I, Emami MR, Rashidi A (2021) Investigation and optimization of the behavior of heat transfer and flow of MWCNT-CuO hybrid nanofluid in a brazed plate heat exchanger using response surface methodology. International Communications in Heat and Mass Transfer 122:105175.