Evaluation of structural analysis of tunnel segmental lining using beam-spring method and force-method (Case study: Chamshir water conveyance tunnel) | ||
| Journal of Mining and Environment | ||
| مقاله 62، دوره 8، شماره 1، فروردین 2017، صفحه 111-130 اصل مقاله (1.11 M) | ||
| نوع مقاله: Case Study | ||
| شناسه دیجیتال (DOI): 10.22044/jme.2016.573 | ||
| نویسندگان | ||
| M. Nikkhah* 1؛ Seyed S. Mousavi1؛ Sh. Zare1؛ O. Khademhosseini2 | ||
| 1School of Mining, Petroleum & Geophysics Engineering, Shahrood University of Technology, Shahrood, Iran | ||
| 2School of Civil Engineering, Shahrood University of Technology, Shahrood, Iran | ||
| چکیده | ||
| The joints between segmental rings can withstand a certain amount of bending moment as well as axial and shear forces. Generally, in the structural analysis of tunnel segmental lining, the joints can be modeled as elastic hinges or rotational springs, and their rigidity should be demonstrated in terms of the rigidity of the joints or their rotational stiffness. Therefore, the bending moment acting on the tunnel lining is reduced. Hence, the tunnel designers are free to choose a lining with a lower cost. In this research work, especially considering the joints, the structural analysis of the segmental lining with variation in the flexural stiffness of the joints ( ), soil resistance coefficient ( ), number of segmental lining joints, and joint arrangement of segmental lining were carried out by the Force-Method equations. The imposed bending moment and axial forces were computed based on the Beam-Spring method, which is widely used to analyze the internal forces of segmental lining, and compared them with the results of the Force-Method equations. Then the effects of joint arrangement patterns and joint rotational spring stiffness on the results of the Beam-Spring analysis were evaluated. Finally, the optimum characteristics of the reinforced concrete segmental lining design were evaluated using the interaction diagram of bending moments and axial forces. The results obtained showed that the presented pattern for the segmental lining at the Chamshir tunnel was imposed against the external pressures on the segmental lining with an acceptable safety factor. | ||
| کلیدواژهها | ||
| Tunnel؛ Design؛ Segmental Lining؛ Joints؛ Beam-Spring method | ||
| اصل مقاله | ||
|
[1]. Kim, H.J. and Eisenstein, Z. (2006). Prediction of Tunnel Lining Loads Using Correction Factors. Engineering Geology. 85 (3-4): 302-312. [2]. Kim, S.H., Pelizza, S. and Kim, J.S. (2006). A study of Strength Parameters in the Reinforced Ground by Rock Bolts. Tunneling and Underground Space Technology. 21(3-4): 378-379. [3]. Wood, A.M. (1975). The Circular Tunnel in Elastic Ground. Geotechnique. 25 (1): 115-127. [4]. Bickel, J.O., Kuesel, T.R. and King, E.H. (1996). Tunnel Engineering Handbook, Chapman & Hall, United States of America. [5]. Koyama, Y. and Nishimura, T. (1998). Design of Lining Segment of Shield Tunnel Using a Beam – Spring Model, Quarterly Report of Railway Technical Research Institute. 39 (1). [6]. Mashimo, H. and Ishimura, T. (2003). Evaluation of the Load on a Shield Tunnel Lining in Gravel, Public Works Research Institute, Independent Administrative Institution, Tsukuba, Japan. [7]. Lee, K.M. and Ge, X.W. (2001). The Equivalent of the Jointed Shield Driven Tunnel Lining to a Continuous Ring Structure. Canadian Geotechnical Journal. 38(3): 461-483. [8]. Lee, K.M., Hou, X.Y., Ge, X.W. and Tang, Y. (2001). An Analytical Solution for a Jointed Shield-Driven Tunnel Lining. International Journal for Numerical and Analytical Methods in Geomechanics. 25 (4): 365-390. [9]. Koyama, Y. (2003). Present Status and Technology of Shield Tunneling Method in Japan. Tunneling and Underground Space Technology. 18 (2-3): 145-159. [10]. Lu, L., Lu, X. and Fan, P. (2011). Full-Ring Experimental Study of The Lining Structure of Shanghai Changjiang Tunnel. Civil Engineering and Architecture. 45 (8): 732-739. ISSN:1934-7359. [11]. Teachavorasinskun, S. and Chub-uppakarn, T. (2010). Influence of Segmental Joints on Tunnel [12]. Arnau, O. and Molins, C. (2012). Three dimensional structural response of segmental tunnel linings, Engineering Structures. 44: 210-221. [13]. Arnau, O. and Molins, C. (2011a). Experimental and analytical study of the structural response of segmental tunnel linings based on an in situ loading test. Part 1: Test configuration and execution. Tunneling and Underground Space Technology. 26: 764-777. [14]. Arnau, O. and Molins, C. (2011b). Experimental and analytical study of the structural response of segmental tunnel linings based on an in situ loading test. Part 2: Numerical simulation. Tunneling and Underground Space Technology. 26: 778-788. [15]. Do, N. and Dias, D. (2012). 2D numerical investigation of segmental tunnel lining behavior. Tunneling and Underground Space Technology. 37: 115-127. [16]. Li, X. and Yan, Z. (2015). Experimental and analytical study on longitudinal joint opening of concrete segmental lining. Tunneling and Underground Space Technology. 46: 52-63. [17]. Zhong, X., Zhu, W., Huang, Z. and Han, Y. (2006). Effect of joint structure on joint stiffness for shield tunnel lining. Tunneling and Underground Space Technology. 21: 406- 407. [18]. Yu, H.T., Yuan, Y., Qiao, Z.Z., Gu, Y., Yang, Z.H. and Li, X.D. (2013). Seismic analysis of a long tunnel based on multi-scale method. Engineering Structure. 49: 572-587. [19]. El Naggar, H. and Hinchberger, S.D. (2008). An analytical solution for jointed tunnellinings in elastic soil or rock. Canadian Geotech. Journal. 45 (11): 1572-1593. [20]. Iranian Oil Operating Companies (IOOC). (1996). Gachsaran Geological Map. 1: 100,000. [21]. AFTES – WG7, Considerations on the Usual Methods of Tunnel Lining Design. (1993). French Tunneling and Underground Engineering Association, Working Group No. 7 - Temporary Supports and Permanent Lining. [22]. JSCE, Japanese Standard for Shield Tunneling.(1996). Japan Society of Civil Engineers, The third edition, Tokyo. [23]. Guray, A. (2010). Evaluation of structural analysis used for the design of TBM segmental linings, Master thesis of civil engineering, Middle East Technical University. [24]. Klappers, C., Gruebl, F. and Ostermeier, B. (1999). Structural Analysis of Segmental Lining – Coupled Beam and Spring Analyses Versus 3D FEM Calculations with Shell Elements, Tunneling and Underground Space Technology. 21 ( 3-4). [25]. Wang, J.J. (2005). The Design Considerations for the Segmental Lining of the Hsuehshan Tunnel, International Symposium on Design, Construction and Operation of Long Tunnels, Taiwan. [26]. Tahouni, S. (2004). Reinforce concrete structure design. (in Persian). | ||
|
آمار تعداد مشاهده مقاله: 3,407 تعداد دریافت فایل اصل مقاله: 6,723 |
||